Rear Drive Shaft
Exploded View

| Circular clip | Dust shield | Housing | |||
| Snap ring | Ball cage/steel ball/inner race assembly | Stopper ring | |||
| Boot band | Boot | Shaft | |||
| Joint sub-assembly | |||||
| : Wheel side | |||||
Removal and Installation
WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION
Removal
Remove rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.
Remove brake hose bracket from suspension arm. Refer to Removal and Installation.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to Removal and Installation.
Remove disc rotor.
Remove wheel sensor harness. Refer to Removal and Installation.
Put matching mark
on drive shaft and wheel hub and bearing assembly.

Using lock nut chisel [SST: KV40108800 ( − )] (A), release stacked area of wheel hub lock nut.


Loosen wheel hub lock nut, using a hub lock nut wrench [SST: KV40104001 (NI-53385)] (A).

Set suitable jack under rear lower link.
Remove rear lower link and coil spring. Refer to Removal and Installation.
Using jack to front lower link.
Loosen the front lower link frame side bolt.
Remove cotter pin and nut, and remove front lower link from axle housing.
Remove cotter pin and nut, and remove suspension arm from axle housing.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing assembly from drive shaft. Take out the wheel hub lock nut.

Remove axle housing assembly.
Remove drive shaft from rear final drive assembly.
Use the drive shaft attachment [SST: KV40107500 ( − )] (A) and a sliding hammer (commercial service tool) (B) while inserting tip of the drive shaft attachment between housing and rear final drive assembly.

Use paint or similar substance for matching marks. Never scratch the surface.
Perform inspection after removal. Refer to Inspection.
Installation
WHEEL SIDE
Note the following, and install in the reverse order of removal.
Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
Clean the matching surface of drive shaft and wheel hub and bearing assembly. And then apply paste [service parts (440037S000)] to surface
of joint sub-assembly of drive shaft.
Amount paste 1.0 – 3.0 g (0.04 – 0.10 oz) When installing drive shaft to wheel hub, never align drive shaft staked area
and one of hub bolts
.
Use the following torque range for tightening the wheel hub lock nut.

: 218 – 223 N·m Using lock nut crimp punch [SST: KV40108700 ( − )] (A), stake wheel hub lock nut and drive shaft staked area.


A : 6.2 mm (0.244 in) B : 29.4 – 30.8 mm (1.157 – 1.213 in) Perform the final tightening of each of parts under unladen conditions, which were removed when removing wheel hub and bearing assembly and axle housing.
FINAL DRIVE SIDE
Note the following, and install in the reverse order of removal.
Place the protector [SST: KV38108000 ( - )] (A) onto rear final drive assembly to prevent damage to the rear final drive assembly side oil seal while inserting drive shaft. Slide drive shaft sliding joint and tap with a hammer to install securely.

WITH DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION
Removal
Start engine.
Turn auto height mode control switch to ON, shift the shift position to N and set to normal height.
Turn OFF the electronic air suspension function. Refer to Operation.
Stop engine.
Lift up the vehicle.
Remove rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.
Remove brake hose bracket from suspension arm. Refer to Removal and Installation.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to Removal and Installation.
Remove disc rotor.
Never drop disc rotor.
Remove wheel sensor harness. Refer to Removal and Installation.
Put matching mark
on drive shaft and wheel hub and bearing assembly.

Using lock nut chisel [SST: KV40108800 ( − )] (A), release stacked area of wheel hub lock nut.


Loosen wheel hub lock nut, using a hub lock nut wrench [SST: KV40104001 (NI-53385)] (A).

Support the rear lower link with suitable jack (A) until most horizontal angle with vehicle on the ground.

Loosen the air connector
and perform air bleeding.

Remove air tube
together with air connector
from air spring
.

Loosen rear lower link mounting nuts (frame side). Refer to Removal and Installation.
Remove rear lower link from axle housing. Refer to Removal and Installation.
Using jack to front lower link.
Loosen the front lower link frame side bolt.
Remove cotter pin and nut, and remove front lower link from axle housing.
Remove cotter pin and nut, and remove suspension arm from axle housing.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing assembly from drive shaft. Take out the wheel hub lock nut.

Remove axle housing assembly.
Remove drive shaft from rear final drive assembly.
Use the drive shaft attachment [SST: KV40107500 ( − )] (A) and a sliding hammer (commercial service tool) (B) while inserting tip of the drive shaft attachment between housing and rear final drive assembly.

Perform inspection after removal. Refer to Inspection.
Installation
Install drive shaft to rear final drive assembly, follow the note below.
Place the protector [SST: KV38108000 ( - )] (A) onto rear final drive assembly to prevent damage to the rear final drive assembly side oil seal while inserting drive shaft. Slide drive shaft sliding joint and tap with a hammer to install securely.

Install axle housing assembly.
Install drive shaft to wheel hub and bearing assembly, follow the note below.
Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
Clean the matching surface of drive shaft and wheel hub and bearing assembly. And then apply paste [service parts (440037S000)] to surface
of joint sub-assembly of drive shaft.
Amount paste 1.0 – 3.0 g (0.04 – 0.10 oz) When installing drive shaft to wheel hub, never align drive shaft staked area
and one of hub bolts
.
Install cotter pin and nut, and install suspension arm to axle housing.
Install cotter pin and nut, and install front lower link to axle housing.
Tighten front lower link mounting nuts (frame side).
Install rear lower link to axle housing. Refer to Removal and Installation.
Tighten rear lower link mounting nuts (frame side). Refer to Removal and Installation.
Install wheel hub lock nut, follow the note below.
Use the following torque range for tightening the wheel hub lock nut.

: 218 – 223 N·m Using lock nut crimp punch [SST: KV40108700 ( − )] (A), stake wheel hub lock nut and drive shaft staked area.

Use the following range for stacking the whell hub lock nut.

A : 6.2 mm (0.244 in) B : 29.4 – 30.8 mm (1.157 – 1.213 in)
Install wheel sensor harness. Refer to Removal and Installation.
Install disc rotor.
Install brake caliper assembly. Refer to Removal and Installation.
Install brake hose bracket to suspension arm. Refer to Removal and Installation.
Install air tube
and air connector
together to air spring
.

Start engine.
Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.
Remove suitable jack from rear lower link.
Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.
Stop engine.
Install rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.
Lift down the vehicle.
Start engine.
Perform pressure measurements using CONSULT. Refer to Work Support.
Perform the height sensor calibration using CONSULT. Refer to Work Support.
Use CONSULT and vehicle to the normal height. Refer to Work Support.
Turn ON the electronic air suspension function. Refer to Operation.
Stop engine.
Perform the final tightening of each of parts under unladen conditions, which were removed when removing wheel hub and bearing assembly and axle housing.
Perform inspection after installation. Refer to Inspection.
Disassembly and Assembly
WHEEL SIDE
Disassembly
Fix shaft with a vise.
Remove dust shield from joint sub-assembly.
Remove boot bands and then remove boot from joint sub-assembly.
Screw the drive shaft puller (commercial service tool) (A) 30 mm (1.18 in) or more into the thread of joint sub-assembly, and remove joint sub-assembly from shaft.

Remove circular clip from shaft.
Remove boot from shaft.
Assembly
Clean old grease on joint sub-assembly with paper waste.
Fill serration slot joint sub-assembly
with NISSAN genuine grease
or equivalent until the serration slot and ball groove become full to the brim.

Install boot and boot bands to shaft.
Remove the tape wrapped around the serrated on shaft.
Position circular clip on groove at the shaft edge.
Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with circular clip joint sub-assembly.
Install joint sub-assembly to shaft using plastic hammer.

Pull the joint sub-assembly in the axial direction away from transaxle assembly. Confirm that the joint sub assembly cannot be pulled out.
Apply the balance of the specified amount of grease into the boot inside from large diameter side of boot.
| Grease amount | : Refer to Drive Shaft. |
Install the boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown below by inserting the suitable tool into inside of the boot from the large diameter side of boot and discharging the inside air.
| L | : Refer to Drive Shaft. |
Securely the boot with boot bands using the boot band crimp tool [SST: KV40107300 (NI-51751)] (A).

| Specified value | |
| M | : 1.0 - 4.0 mm (0.04 - 0.16 in) |
Secure joint sub-assembly and shaft, and then make sure that they are in the correct position when rotating boot. Install them with boot band when boot installation positions become incorrect.
Install dust shield to joint sub-assembly.
FINAL DRIVE SIDE
Disassembly
Fix shaft with a vise.
Remove circular clip from housing.
Remove dust shield from housing.
Remove boot bands, and then remove boot from housing.
Put matching marks on housing and shaft.
Remove stopper ring with suitable tool, and pull out housing.

Put matching marks on ball cage/steel ball/inner race assembly and shaft.
Remove snap ring, then remove ball cage/steel ball/inner race assembly from shaft.

Remove boot from shaft.
Assembly
Remove old grease on housing with paper waste.
Install boot and boot bands to shaft.
Remove the tape wrapped around the serrated on shaft.
Install ball cage/steel ball/inner race assembly
, align it with the matching marks on shaft
put during the removal.

Secure ball cage/steel ball/inner race assembly onto shaft with snap ring
.
Apply the appropriate amount of grease onto housing and sliding surface.
| Grease amount | : Refer to Drive Shaft. |
Install housing.
Install stopper ring to housing.
After installed, pull shaft to check engagement between housing and stopper ring.
Install boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent the deformation of the boot, adjust the boot installation length (L) to the value shown below by inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging inside air.
| L | : Refer to Drive Shaft. |
Secure the large and small ends of the boot with boot bands using the boot band crimp tool [SST: KV40107300 (NI-51751)] (A).

| Specified value | |
| M | : 1.0 - 4.0 mm (0.04 - 0.16 in) |
Check that location stays in the correct position when housing and shaft are secured and boot is rotated.
Install circular clip to housing.
Install dust shield to housing.
Perform inspection after assembly. Refer to Inspection.
Inspection
INSPECTION AFTER REMOVAL
Move joint up/down, left/right, and in the axial direction. Check for any rough movement or significant looseness.
Check boot for cracks or other damage, and also for grease leakage.

If a malfunction is found, disassemble drive shaft, and then replace with new one.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are any abnormal condition.
Joint Sub-Assembly (Wheel Side)
Check the following:
Joint sub-assembly for rough rotation and excessive axial looseness.
The inside of the joint sub-assembly for entry of foreign material.
Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Ball cage/steel ball/inner race assembly (Final Drive Side)
Replace housing and ball cage/steel ball/inner race assembly if there is scratching or wear of housing steel ball contact surface or steel ball.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to Inspection.
Perform the height sensor calibration. (With dynamic digital suspension and electronic air suspension) Refer to Work Support.