Brake System RHD

Brake master cylinder

In this manual: Brake System RHD
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Exploded View

2WD

1. Reservoir cap

1. Reservoir cap
2. Oil strainer
3. Reservoir tank
4. Cylinder body
5. O-ring
6. Grommet
7. Pin

lubricant: Apply polyglycol ether
lubricant
: N·m (kg-m, ft-lb): Apply brake fluid.


: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly.

4WD

1. Reservoir cap

1. Reservoir cap
2. Oil strainer
3. Reservoir tank
4. Cylinder body
5. Pin
6. O-ring
7. Grommet

lubricant: Apply polyglycol ether
lubricant
: N·m (kg-m, ft-lb): Apply brake fluid.


: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly.

Removal and Installation

REMOVAL

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake tube. If this is not complied with, brake fluid may splash.

1. Perform inspection before removal. Refer to BR-110, "Inspection". 2. Depress the brake pedal several times to release the vacuum pressure from the brake booster. 3. Drain brake fluid. Refer to BR-80, "Draining". 4. Disconnect the brake fluid level switch harness connector.

5. Separate the brake tube from master cylinder assembly with a flare nut wrench (A).

CAUTION:
Never scratch the flare nut and the brake tube.

6. Remove the master cylinder assembly.

CAUTION:
• Never deform or bend the brake tubes.

• Never depress the brake pedal after the master cylinder assembly is removed.

• The piston (A) of the master cylinder assembly is

• The piston (A) of the master cylinder assembly is exposed. Never damage it when removing the master cylinder.

• The piston may drop off when pulled out strongly. Never hold the piston. Hold the cylinder body when handling the master cylinder assembly.

7. Remove the O-ring.

INSTALLATION

INSTALLATION

Note the following, and install in the reverse order of removal.

• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water. • Never depress the brake pedal while removing the brake tube. If this is not complied with, brake fluid may splash. • Never depress the brake pedal after the master cylinder assembly is removed.

• Apply polyglycol ether based lubricant to the brake booster [see (A) in the figure] when installing the master cylinder assembly to the brake booster.

• The piston (A) of the master cylinder assembly is exposed. Never

• The piston (A) of the master cylinder assembly is exposed. Never damage it when handling the master cylinder.

• Check that no dirt and dust are present on the piston before installation.

Clean it with new brake fluid if necessary.

• The piston may drop off when pulled strongly. Never hold the piston.

Hold the cylinder body when handling the master cylinder assembly. • Never reuse the O-ring.

• Never deform or bend the brake tubes.

• Temporarily tighten the brake tube flare nut to the master cylinder

• Temporarily tighten the brake tube flare nut to the master cylinder assembly by hand. Then tighten it to the specified torque with a flare nut torque wrench (A). Refer to BR-91, "FRONT : Exploded View".

• Perform the air bleeding. Refer to BR-81, "Bleeding Brake System" • Perform inspection after installation. Refer to BR-110, "Inspection".

Disassembly and Assembly

Disassembly and Assembly

DISASSEMBLY

CAUTION:
• Never disassemble the cylinder body.

• Remove the reservoir tank only when necessary.

1. Fix the master cylinder assembly to a vise.

CAUTION:
• Always set copper plates or cloth between vise grips when fixing the cylinder body to a vise.

• Never overtighten the vise.

2. Remove the reservoir tank mounting pin with a pin punch (A) [4 mm (0.157 in)].

3. Remove the reservoir tank and grommet from the cylinder bod

ASSEMBLY

ASSEMBLY

CAUTION:
• Never use mineral oils such as kerosene or gasoline and rubber grease during the cleaning and assembly process. • Never allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.

• Never drop the when installing. The parts must not be reused if they are dropped.

1. Apply new brake fluid to the grommet and install it to the cylinder body.

CAUTION:
Never reuse the grommets.
2. Install the reservoir tank to the cylinder body.

3. Fix the cylinder body to a vise.

CAUTION:
• Place the reservoir tank with the chamfered pin hole ()
) facing up. • Always set copper plates or cloth between vise grips when fixing the cylinder body to a vise.

• Never overtighten the vise.

4. Tilt the reservoir tank so that a mounting pin can be inserted. Insert a

4. Tilt the reservoir tank so that a mounting pin can be inserted. Insert a mounting pin. Return the reservoir tank to the horizontal position. Insert another mounting pin into the pin hole on the opposite side in the same manner after the mounting pin passes through the cylinder body pin hole.

CAUTION:
Never reuse the mounting pin.

Inspection

INSPECTION BEFORE REMOVAL

Check the brake fluid level switch.

• Without ESP: Refer to BRC-73, "Component Inspection".

• With ESP: Refer to BRC-194, "Component Inspection".

INSPECTION AFTER INSTALLATION

Check the following items and replace if necessary.

• Check the master cylinder for deformation, twist, contact with other parts or looseness of connection.

• Check for fluid leakage from connection. Refer to BR-97, "FRONT : Inspection".

CAUTION:
If the fluid leakage is present, retighten to the specified torque. Replace if necessary.