Brake System RHD

Brake piping

In this manual: Brake System RHD
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~13min read

Front : Exploded View

WITHOUT ESP

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Brake tube
4. Connector bracket
5. Connector
6. ABS actuator and electric unit (control unit)
7. Lock plate
8. Brake hose
9. Union bolt
10. Copper washer

A. To rear brake tube

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

WITH ESP

MR16DDT

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Brake tube
4. Connector bracket
5. Connector
6. ABS actuator and electric unit (control unit)
7. Lock plate
8. Brake hose
9. Union bolt
10. Copper washer

A. To rear brake tube

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

HR16DE

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Brake tube
4. Connector bracket
5. Connector
6. ABS actuator and electric unit (control unit)
7. Lock plate
8. Brake hose
9. Union bolt
10. Copper washer

A. To rear brake tube

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

K9K

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Brake tube
4. Connector bracket
5. Connector
6. ABS actuator and electric unit (control unit)
7. Lock plate
8. Brake hose
9. Union bolt
10. Copper washer

A. To rear brake tube

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

Front : Hydraulic Piping

2WD

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Front disc brake
4. ABS actuator and electric unit (control unit)
5. Connector
6. Rear disc brake

A. Brake tube
B. Brake hose

: Union bolt: Flare nut
4WD: Union bolt


4WD

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Front disc brake
4. ABS actuator and electric unit (control unit)
5. Connector
6. Rear disc brake

A. Brake tube
B. Brake hose

: Union bolt: Flare nut
Front : Removal and Installation: Union bolt


Front : Removal and Installation

REMOVAL

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied with, brake fluid may splash.

1. Remove tires. 2. Drain brake fluid. Refer to BR-80, "Draining".

3. Loosen the flare nut (1) with a flare nut wrench (A) and separate the brake tube (2) from the brake hose (3).

CAUTION:
• Never scratch the flare nut and the brake tube. • Never bend sharply, twist or strongly pull out the brake hoses and tubes.

• Cover open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.

4. Remove the union bolt (1) and copper washers (2), and remove

4. Remove the union bolt (1) and copper washers (2), and remove the brake hose (3) from the brake caliper assembly.

5. Remove the lock plate (4) and remove the brake hose.

INSTALLATION

INSTALLATION

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied with, brake fluid may splash.

1. Assemble the union bolt (1) and the copper washer (2) to the brake hose.

CAUTION:
Never reuse the copper washe

r.

2. Align the brake hose pin (A) with the brake caliper assembly projection (B), and tighten the union bolt (1) to the specified torqu

3. Install the brake tube (2) to the brake hose (1), temporarily

3. Install the brake tube (2) to the brake hose (1), temporarily tighten the flare nut (3) by hand until it does not rotate further, and fix the brake hose to the bracket (5) with the lock plate (4).

CAUTION:
Check that all brake hoses and brake tubes are not twisted and bent.
4. Tighten the flare nut to the specified torque with a flare nut

4. Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

CAUTION:
Never scratch the flare nut and the brake tube.

5. Refill with new brake fluid and perform the air bleeding. Refer to BR-81, "Bleeding Brake System".

CAUTION:
Never reuse drained brake fluid.
6. Install tires. Refer to WT-7, "Exploded View".

7. Perform inspection after installation. Refer to BR-97, "FRONT : Inspection".

Front : Inspection

Front : Inspection

INSPECTION AFTER INSTALLATION

1. Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no interference with other components when steering the steering wheel; no looseness at connections.

2. Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately 5 seconds with the engine running. Check for any fluid leakage.

CAUTION:
Retighten the applicable connection to the specified torque and repair any abnormal (damaged, worn or deformed) part if any brake fluid leakage is present.

Rear : Exploded View

2WD (MR16DDT, HR16DE)

1. Brake tube

1. Brake tube
2. Brake hose A
3. Lock plate
4. Brake hose bracket
5. Union bolt
6. Brake hose B
7. Copper washer

A. To connector

N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

2WD (K9K)

1. Brake tube

1. Brake tube
2. Brake hose A
3. Lock plate
4. Brake hose bracket
5. Union bolt
6. Brake hose B
7. Copper washer

A. To connector

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

4WD

1. Brake tube

1. Brake tube
2. Brake hose A
3. Lock plate
4. Brake hose bracket
5. Brake hose B
6. Union bolt
7. Copper washer

A. To connector

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

Rear : Hydraulic Piping

2WD

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Front disc brake
4. ABS actuator and electric unit (control unit)
5. Connector
6. Rear disc brake

A. Brake tube
B. Brake hose

: Union bolt: Flare nut
4WD: Union bolt


4WD

1. Brake booster

1. Brake booster
2. Master cylinder assembly 3. Front disc brake
4. ABS actuator and electric unit (control unit)
5. Connector
6. Rear disc brake

A. Brake tube
B. Brake hose

: Union bolt: Flare nut
Rear : Removal and Installation: Union bolt


Rear : Removal and Installation

REMOVAL

2WD

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied with, brake fluid may splash.

1. Remove tires. 2. Drain brake fluid. Refer to BR-80, "Draining".

3. Loosen the flare nut (1) with a flare nut wrench (A) and separate the brake tube (2) from the brake hose A (3).

CAUTION:
• Never scratch the flare nut and the brake tube. • Never bend sharply, twist or strongly pull out the brake hoses and tubes.

• Cover open end of brake tubes and hoses when disconnecting to prevent entrance of dirt

.

4. Remove the lock plate (4) and remove the brake hose A.

5. Loosen the flare nut (1) with a flare nut wrench (A) and separate

5. Loosen the flare nut (1) with a flare nut wrench (A) and separate the brake tube (2) from the hose B (3).

CAUTION:
• Never scratch the flare nut and the brake tube. • Never bend sharply, twist or strongly pull out the brake hoses and tubes.

• Cover open end of brake tubes and hoses when disconnecting to prevent entrance of dirt

.

6. Remove the lock plate (4) from brake hose bracket (5).

7. Remove the union bolt (1) and copper washers (2), and remove

7. Remove the union bolt (1) and copper washers (2), and remove the brake hose B (3) from the brake caliper assembly.

4WD

4WD

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied with, brake fluid may splash.

1. Remove tires. 2. Drain brake fluid. Refer to BR-80, "Draining".

3. Loosen the flare nut (1) with a flare nut wrench (A) and separate the brake tube (2) from the hose A (3).

CAUTION:
• Never scratch the flare nut and the brake tube. • Never bend sharply, twist or strongly pull out the brake hoses and tubes.

• Cover open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.

4. Remove the lock plate (4) and remove the brake hose A.

5. Loosen the flare nut (1) with a flare nut wrench (A) and separate

5. Loosen the flare nut (1) with a flare nut wrench (A) and separate the brake tube (2) from the hose B (3).

CAUTION:
• Never scratch the flare nut and the brake tube. • Never bend sharply, twist or strongly pull out the brake hoses and tubes.

• Cover open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.

6. Remove the lock plate (4) from brake hose bracket (5).

7. Remove the union bolt (1) and copper washers (2), and remove

7. Remove the union bolt (1) and copper washers (2), and remove the brake hose B (3) from the brake caliper assembly.

INSTALLATION

INSTALLATION

2WD

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied with, brake fluid may splash.

1. Assemble the union bolt (1) and the copper washer (2) to the brake hose B.

CAUTION:
Never reuse the copper washer.

2. Align the brake hose B L-pin (A) with the brake caliper assembly hole (B), and tighten the union bolt (1) to the specified torque.

3. Install the brake tube (2) to the brake hose B (1), temporarily

3. Install the brake tube (2) to the brake hose B (1), temporarily tighten the flare nut (3) by hand until it does not rotate further, and fix the brake hose B to the brake hose bracket (5) with the lock plate (4).

CAUTION:
Check that all brake hoses and brake tubes are not twisted and bent.
4. Tighten the flare nut to the specified torque with a flare nut

4. Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

CAUTION:
Never scratch the flare nut and the brake tube.
5. Install the brake tube (2) to the brake hose A (1), temporarily

5. Install the brake tube (2) to the brake hose A (1), temporarily tighten the flare nut (3) by hand until it does not rotate further, and fix the brake hose with the lock plate (4).

CAUTION:
Check that all brake hoses and brake tubes are not twisted and bent.
6. Tighten the flare nut to the specified torque with a flare nut

6. Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

CAUTION:
Never scratch the flare nut and the brake tube.

7. Refill with new brake fluid and perform the air bleeding. Refer to BR-81, "Bleeding Brake System".

CAUTION:
Never reuse drained brake fluid.
8. Install tires. Refer to WT-7, "Exploded View".

9. Perform inspection after installation. Refer to BR-105, "REAR : Inspection".

4WD

4WD

CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied with, brake fluid may splash.

1. Assemble the union bolt (1) and the copper washer (2) to the brake hose B.

CAUTION:
Never reuse the copper washer.

2. Align the brake hose B L-pin (A) with the brake caliper assembly hole (B), and tighten the union bolt (1) to the specified torque.

3. Install the brake tube (2) to the brake hose B (1), temporarily

3. Install the brake tube (2) to the brake hose B (1), temporarily tighten the flare nut (3) by hand until it does not rotate further, and fix the brake hose B to the brake hose bracket (5) with the lock plate (4).

CAUTION:
Check that all brake hoses and brake tubes are not twisted and bent.
4. Tighten the flare nut to the specified torque with a flare nut

4. Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

CAUTION:
Never scratch the flare nut and the brake tube.
5. Install the brake tube (2) to the brake hose A (3), temporarily

5. Install the brake tube (2) to the brake hose A (3), temporarily tighten the flare nut (1) by hand until it does not rotate further, and fix the brake hose A to the bracket with the lock plate (4).

CAUTION:
Check that all brake hoses and brake tubes are not twisted and bent.
6. Tighten the flare nut to the specified torque with a flare nut

6. Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

CAUTION:
Never scratch the flare nut and the brake tube.

7. Refill with new brake fluid and perform the air bleeding. Refer to BR-81, "Bleeding Brake System".

CAUTION:
Never reuse drained brake fluid.
8. Install tires. Refer to WT-7, "Exploded View".

9. Perform inspection after installation. Refer to BR-105, "REAR : Inspection".

Rear : Inspection

Rear : Inspection

INSPECTION AFTER INSTALLATION

1. Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no looseness at connections.

2. Depress the brake pedal with a force of 785 N (80kg, 176 lb) and hold down the pedal for approximately 5 seconds with the engine running. Check for any fluid leakage.

CAUTION:
Retighten the applicable connection to the specified torque and repair any abnormal (damaged, worn or deformed) part if any brake fluid leakage is present.