Brake System RHD

Vacuum lines

In this manual: Brake System RHD
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

MR16DDT : Removal and Installation

REMOVAL

1. Remove the vacuum hose and vacuum piping.

2. Perform inspection after removal. Refer to BR-115, "MR16DDT : Inspection".

INSTALLATION

Note the following, install the vacuum hose.

• When installing vacuum hose, insert it until its tip reaches the back-end of length (A) or further as shown in the figure.

CAUTION:
Never use lubricating oil during assembly.

A : 24 mm (0.95 in) or more

- Face the paint mark of vacuum hose (engine side) upward to assemble. - Face the paint mark of vacuum hose (brake booster side) to the vehicle front side to assemble.

- For clamp mounting direction (the orientation of pawl), refer to BR- 115, "MR16DDT : Exploded View".

MR16DDT : Inspection

INSPECTION AFTER REMOVAL

Appearance
Check for correct assembly, damage and deterioration.

Check Valve Airtightness • Use a handy vacuum pump (A) to check.

When connected to the booster side (B): Vacuum should decrease within 1.3 kPa (9.8 mmHg, 0.38 inHg, 0.013 bar) for 15 seconds under a vacuum of −66.7 kPa (−500 mmHg, −19.70 inHg, −0.667 bar).

When connected to the engine side (C): Vacuum should not exist.

• Replace vacuum hose if vacuum hose is malfunctioning.

HR16DE : Exploded View

HR16DE : Exploded View

1. Clamp

1. Clamp
2. Vacuum hose (built-in check valve)

A. To intake manifold B. Paint mark
C. Stamp indicating engine direction D. To brake booster

HR16DE : Removal and Installation

REMOVAL

1. Remove the vacuum hose and vacuum piping.

2. Perform inspection after removal. Refer to BR-117, "HR16DE : Inspection".

INSTALLATION

Note the following, install the vacuum hose.

• When installing vacuum hose, insert it until its tip reaches the back-end of length (A) or further as shown in the figure.

CAUTION:
Never use lubricating oil during assembly.

A : 24 mm (0.95 in) or more

- Face the paint marks upward to assemble.

- For clamp mounting direction (the orientation of pawl), refer to BR- 116, "HR16DE : Exploded View".

HR16DE : Inspection

HR16DE : Inspection

INSPECTION AFTER REMOVAL

Appearance
Check for correct assembly, damage and deterioration.

Check Valve Airtightness • Use a handy vacuum pump (A) to check.

When connected to the booster side (B): Vacuum should decrease within 1.3 kPa (9.8 mmHg, 0.38 inHg, 0.013 bar) for 15 seconds under a vacuum of −66.7 kPa (−500 mmHg, −19.70 inHg, −0.667 bar).

When connected to the engine side (C): Vacuum should not exist.

• Replace vacuum hose assembly if vacuum hose and check valve are malfunctioning.

K9K : Exploded View

K9K : Exploded View

1. Clamp

1. Clamp
2. Vacuum hose
3. Vacuum piping
4. Vacuum hose (built-in check valve) 5. Connector

A. To brake booster
B. Paint mark
C. Stamp indicating engine direction D. To vacuum pump

K9K : Removal and Installation

REMOVAL

1. Remove air duct and air cleaner case. Refer to EM-280, "Removal and Installation".

2. Remove the vacuum hose and connector.

INSTALLATION

Note the following, install the vacuum hose.

• When installing vacuum hose, insert it until its tip reaches the back-end of length (A) or further as shown in the figure.

CAUTION:
Never use lubricating oil during assembly.

A : 24 mm (0.95 in) or more

- Face the paint mark of vacuum hose (built-in check valve, connector side) upward to assemble. - Face the other paint marks to vehicle front side to assemble.

- For clamp mounting direction (the orientation of pawl), refer to BR- 117, "K9K : Exploded View".

K9K : Inspection

K9K : Inspection

INSPECTION AFTER REMOVAL

Appearance
Check for correct assembly, damage and deterioration.

Check Valve Airtightness • Use a handy vacuum pump (A) to check.

When connected to the booster side (B): Vacuum should decrease within 1.3 kPa (9.8 mmHg, 0.38 inHg, 0.013 bar) for 15 seconds under a vacuum of −66.7 kPa (−500 mmHg, −19.70 inHg, −0.667 bar).

When connected to the engine side (C): Vacuum should not exist.

• Replace vacuum hose assembly if vacuum hose and check valve are malfunctioning.

Front disc brake