Brake Control System with ESP

C1176 stop lamp SW2

In this manual: Brake Control System with ESP
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

1. Turn the ignition switch OFF to ON.With CONSULT-III.


1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ABS”.

Is DTC “C1176” detected? YES >> Proceed to BRC-199, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

NOTE

:
DTC “C1176” may be detected when the brake pedal and the accelerator pedal are simultaneously depressed for 1 minute or more while driving the vehicle. This is not a malfunction.

1.INTERVIEW FROM THE CUSTOMER

Check if the brake pedal and the accelerator pedal are simultaneously depressed for 1 minute or more while driving the vehicle.

Is there such a history? YES >> GO TO 2.

NO >> GO TO 3.

2.PERFORM SELF-DIAGNOSIS

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”. 2. Turn the ignition switch OFF, and wait 10 seconds or more.

3. Start the engine.

CAUTION:
Never start the vehicle.
4. Depress the brake pedal several times.

5. Perform self-diagnosis for “ABS”.

Is DTC “C1176” detected? YES >> GO TO 3.

NO >> INSPECTION END

3.CHECK BRAKE SWITCH/BRAKE PEDAL POSITION SWITCH CLEARANCE 1. Turn the ignition switch OFF.

2. Check brake switch/brake pedal position switch clearance.

- LHD: Refer to BR-9, "Inspection and Adjustment".

- RHD: Refer to BR-77, "Inspection and Adjustment".

Is the inspection result normal? YES >> GO TO 5.

NO >> Adjust brake switch/brake pedal position switch clearance. GO TO 4.

• LHD: Refer to BR-77, "Inspection and Adjustment".

• RHD: Refer to BR-77, "Inspection and Adjustment".

4.CHECK DATA MONITOR (1)

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”. 2. Turn the ignition switch OFF, and wait 10 seconds or more.

3. Start the engine.

CAUTION:
Never start the vehicle.

4. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW2” according to this order. Check that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to BRC-136, "Reference Value".

Is the inspection result normal? YES >> INSPECTION END

NO >> GO TO 5.

5.CHECK BRAKE SWITCH/BRAKE PEDAL POSITION SWITCH

Check brake switch/brake pedal position switch. Refer to BRC-177, "Component Inspection".

Is the inspection result normal? YES >> GO TO 7.

NO >> Replace brake switch/brake pedal position switch. GO TO 6.

• LHD: Refer to BR-21, "Removal and Installation".

• RHD: Refer to BR-89, "Removal and Installation".

6.CHECK DATA MONITOR (2)

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”. 2. Turn the ignition switch OFF, and wait 10 seconds or more.

3. Start the engine.

CAUTION:
Never start the vehicle.

4. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW2” according to this order. Check that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to BRC-136, "Reference Value".

Is the inspection result normal? YES >> INSPECTION END NO >> GO TO 7.

7.CHECK CONNECTOR AND TERMINAL 1. Turn the ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) harness connector. 3. Check ABS actuator and electric unit (control unit) harness connector for disconnection or looseness. 4. Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector. 5. Disconnect brake switch/brake pedal position switch harness connector. 6. Check brake switch/brake pedal position switch harness connector for disconnection or looseness.

7. Check brake switch/brake pedal position switch pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> GO TO 9.

NO >> Repair or replace error-detected parts. GO TO 8.

8.CHECK DATA MONITOR (3)

1. Connect ABS actuator and electric unit (control unit) harness connector.With CONSULT-III.


1. Connect ABS actuator and electric unit (control unit) harness connector. 2. Connect brake switch/brake pedal position switch harness connector. 3. Erase Self-diagnosis result for “ABS”. 4. Turn the ignition switch OFF, and wait 10 seconds or more.

5. Start the engine.

CAUTION:
Never start the vehicle.

6. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW2” according to this order. Check that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to BRC-136, "Reference Value".

Is the inspection result normal? YES >> INSPECTION END

NO >> GO TO 11.

9.CHECK BRAKE SWITCH/BRAKE PEDAL POSITION SWITCHCIRCUIT (1) 1. Turn the ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) harness connector.

3. Check voltage between ABS actuator and electric unit (control unit) harness connector and ground.

4. Turn the ignition switch ON.

4. Turn the ignition switch ON.

5. Check voltage between ABS actuator and electric unit (control unit) harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-233, "Removal and Installation".

NO >> Repair or replace error-detected parts. GO TO 10.

10.CHECK BRAKE SWITCH/BRAKE PEDAL POSITION SWITCH CIRCUIT (2) 1. Turn the ignition switch OFF. 2. Disconnect brake switch/brake pedal position switch harness connector.

3. Check continuity between ABS actuator and electric unit (control unit) harness connector and brake switch/brake pedal position switch harness connector.

*1: Brake switch (LHD models and RHD models with CVT)

*1: Brake switch (LHD models and RHD models with CVT) *2: Brake pedal position switch (LHD models and RHD models with CVT) *3: Brake switch (RHD models with M/T) *4: Brake pedal position switch (RHD models with M/T)

4. Check continuity between ABS actuator and electric unit (control unit) harness connector and the ground.

Is the inspection result normal?

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-233, "Removal and Installation".

NO >> Repair or replace error-detected parts. GO TO 11.

11.CHECK DATA MONITOR (4)

With CONSULT-III.

1. Connect ABS actuator and electric unit (control unit) harness connector. 2. Connect brake switch/brake pedal position switch harness connector. 3. Erase Self-diagnosis result for “ABS”. 4. Turn the ignition switch OFF, and wait 10 seconds or more.

5. Start the engine.

CAUTION:
Never start the vehicle.

6. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW2” according to this order. Check that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to BRC-136, "Reference Value".

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-233, "Removal and Installation".

Component Inspection

1.CHECK BRAKE SWITCH/BRAKE PEDAL POSITION SWITCH 1. Turn ignition switch OFF.2. Disconnect brake switch/brake pedal position switch harness connector.

3. Check continuity between brake switch/brake pedal position switch harness connector terminals.

Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace brake switch/brake pedal position switch.

• LHD: Refer to BR-21, "Removal and Installation".

• RHD: Refer to BR-89, "Removal and Installation".