Engine Mechanical HR16DE

Engine stand setting

In this manual: Engine Mechanical HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~2min read
NOTE

:
Explained here is how to disassemble with engine stand supporting transaxle surface. When using different type of engine stand, note with difference in steps and etc.

1. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the engine. Refer to EM-215, "Exploded View".

2. Install engine to engine stand with the following procedure: a. Remove flywheel or drive plate.

• Secure flywheel (1) with a stopper plate [SST: KV11105210] (A), and remove mounting bolts (M/T models).

• Secure driveplate (1) with a stopper plate [SST: KV11105210]

• Secure driveplate (1) with a stopper plate [SST: KV11105210] (A), and remove mounting bolts (CVT models).

CAUTION:

CAUTION:
• Never disassemble them. • Never place them with signal plate facing down. • When handling signal plate, take care not to damage or scratch them.

• Handle signal plate in a manner that prevents them from becoming magnetized.

b. Remove pilot converter (1) from the rear end of the crankshaft.

Use a pilot bush puller [SST: ST16610000] (A), if necessary.

c. Lift the engine with a hoist to install it onto widely use engine stand.

c. Lift the engine with a hoist to install it onto widely use engine stand.

CAUTION:
• Use the engine stand that has a load capacity [approximately 150 kg (331 lb) or more] large enough for supporting the engine weight.

• If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the potential risk of overturning stand.

- Intake manifold: Refer to EM-163, "Exploded View". - Exhaust manifold: Refer to EM-166, "Removal and Installation".

- Rocker cover: Refer to EM-178, "Exploded View".

NOTE

:
The figure shows an example of widely used engine stand (A) that can support mating surface of transaxle with flywheel removed.

CAUTION:
Before removing the hanging chains, check the engine stand is stable and there is no risk of overturning.
3. Drain engine oil. Refer to LU-26, "Draining".

3. Drain engine oil. Refer to LU-26, "Draining".

CAUTION:
Be sure to clean drain plug and install with new drain plug washer.

4. Drain engine coolant by removing water drain plug (1) from inside of the engine.

Tightening torque : Refer to EM-227, "Exploded: Engine front


Tightening torque : Refer to EM-227, "Exploded View".

Use Genuine Liquid Gasket or equivalent.
Engine unit