Engine Mechanical HR16DE

Oil pan (upper)

In this manual: Engine Mechanical HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Exploded View

With Oil Cooler

1. Rear oil seal

1. Rear oil seal
2. O-ring
3. Oil pan (upper)
4. Oil pump chain tensioner (for oil pump drive chain)
5. Oil pump drive chain 6. Crankshaft sprocket
7. Oil pump sprocket
8. Oil pump
9. O-ring
10. O-ring
11. Oil pan (lower)
12. Oil pan drain plug
13. Drain plug washer
14. Oil level sensor
15. Relief valve
16. Connector bolt
17. Oil filter
18. Oil cooler
19. O-ring

A. Refer to EM-182
B. Refer to LU-28
C. Oil pan (lower) side

disassembly.: Always replace after every
disassembly.

: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
: Sealing point: N·m (kg-m, ft-lb)
: Should be lubricated with oil.: Sealing point
With Out Oil Cooler: Should be lubricated with oil.


With Out Oil Cooler

1. Rear oil seal

1. Rear oil seal
2. O-ring
3. Oil pan (upper)
4. Oil pump chain tensioner (for oil pump drive chain)
5. Oil pump drive chain 6. Crankshaft key
7. Crankshaft sprocket
8. Oil pump sprocket
9. Oil pump
10. O-ring
11. O-ring
12. Oil pan drain plug
13. Drain plug washer
14. Oil pan (lower)
15. Oil filter
16. Oil filter stud bolt

A. Refer to EM-182
B. Refer to LU-28
C. Oil pan (lower) side

disassembly.: Always replace after every
disassembly.

: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
: Sealing point: N·m (kg-m, ft-lb)
: Should be lubricated with oil..: Sealing point
Removal and Installation: Should be lubricated with oil..


Removal and Installation

NOTE

:
The oil strainer and oil pump are included in the oil pan (upper). Individual disassembly is prohibited.

REMOVAL

1. Remove the oil pan (lower). Refer to EM-169, "Exploded View". 2. Remove oil pump sprocket and crankshaft sprocket together with oil pump drive chain. Refer to EM-181, "Exploded View".

3. Remove oil pan (upper) with the following procedure.

a. Loosen oil pan (upper) mounting bolts in the reverse of the order as shown in the figure.

: Engine front


b. Insert a flat-bladed offset screwdriver into the arrow (

b. Insert a flat-bladed offset screwdriver into the arrow () in the
) in the figure and open up a crack between the oil pan (upper) cylinder block.

c. Insert the seal cutter [SST: KV10111100] between the oil pan: Engine front


c. Insert the seal cutter [SST: KV10111100] between the oil pan (upper) and cylinder block. Slide seal cutter by tapping on the side of tool with a hammer.

CAUTION:
• Be careful not to damage the mating surface. • A more adhesive liquid gasket is applied compared to previous types when shipped, so it should not be forced off using a screwdriver, etc. outside the indicated location.

• Never remove oil pump and oil strainer from oil pan (upper).

4. Remove rear oil seal from crankshaft.

INSTALLATION

INSTALLATION

1. Install the oil pan (upper) in the following procedure: a. Use scraper to remove old liquid gasket from mating surfaces.

• Also remove the old liquid gasket from mating surface of cylinder block.

• Remove old liquid gasket from the bolt holes and threads.

CAUTION:
Never scratch or damage the mating surfaces when cleaning off old liquid gasket.

b. Install O-ring to the cylinder block.

c. Apply a continuous bead of liquid gasket (C) with the tube presser (commercial service tool) to areas as shown in the figure.

Use Genuine Liquid Gasket or equivalent.

A : 2 mm (0.07 in) protruded to outside B : 2 mm (0.07 in) protruded to rear oil seal mounting side d : 5.5 - 7.5 mm (0.217 - 0.295 in) e : φ4.0 - 5.0 mm (0.157 - 0.197 in) : Engine out side: Engine front side
A : Excess of 2 mm or more outward: Engine out side
A : Excess of 2 mm or more outward B : Excess of 2 mm or more in the rear oil seal mounting direction

CAUTION:

CAUTION:
Attaching should be done within 5 minutes after coating.

d. Tighten bolts in the numerical order as shown in the figure.

CAUTION:: Engine front


CAUTION:
Install avoiding misalignment of both oil pan gasket and Oring.

• The bolts are different according to the installation position.

Refer to the numbers as shown in the figure.

M8×180 mm (7.09 in) : No. 9, 10 M8×25 mm (0.98 in) : No. 3, 4, 7, 8 M8×90 mm (3.54 in) : No. 1, 2, 5, 6

2. Install rear oil seal with the following procedure:

2. Install rear oil seal with the following procedure: CAUTION:
• The installation of rear oil seal should be completed within 5 minutes after installing oil pan (upper).

• Never touch oil seal lip.

a. Wipe off any liquid gasket protruding to the rear oil seal mounting part of oil pan (upper) and cylinder block using a spatula.

b. Apply the liquid gasket lightly to entire outside area of new rear oil seal.

Use Genuine Liquid Gasket or equivalent.

c. Press-fit the rear oil seal using a drift with outer diameter 113 mm (4.45 in) and inner diameter 90 mm (3.54 in) (commercial service tool) (A).

• Press-fit to the dimensions specified as shown in the figure.

• Press-fit to the dimensions specified as shown in the figure.

1 : Rear oil seal
A : Rear end surface of cylinder block b : 0 - 0.5 mm (0 - 0.020 in)

CAUTION:
• Never touch the grease applied to the oil seal lip. • Be careful not to damage the rear oil seal mounting part of oil pan (upper) and cylinder block or the crankshaft.

• Press-fit straight check that oil seal does not curl or tilt.

d. After press-fitting the rear oil seal, completely wipe off any liquid gasket protruding to rear end surface side.

3. Install in the reverse order of removal, for the rest of parts.

Inspection

Inspection

INSPECTION AFTER INSTALLATION

1. Check engine oil level and adjust engine oil. Refer to LU-25, "Inspection". 2. Check for leakage of engine oil when engine is warmed. 3. Stop engine and wait for 10 minutes.

4. Check engine oil level again. Refer to LU-25, "Inspection".