Driveline rear final drive: RTVS

Front oil seal

In this manual: Driveline rear final drive: RTVS
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read
010203040500.40N·mlb·ft
Tightening torque found on this page

Exploded View

1. Rear final drive assembly

1. Rear final drive assembly 2. Front oil seal
3. Companion flange
4. Companion flange lock nut

A. Oil seal lip

: N·m (kg-m, ft-lb): Vehicle front
: Never reuse parts: N·m (kg-m, ft-lb)
: Apply multi purpose grease: Never reuse parts
: Apply gear oil.: Apply multi purpose grease
Removal and Installation: Apply gear oil.


Removal and Installation

REMOVAL

CAUTION:
Verify identification stamp of replacement frequency put in the lower part of gear carrier to determine replacement for collapsible spacer when replacing front oil seal. Refer to “Identification stamp of replacement frequency of front oil seal”. If collapsible spacer replacement is necessary, remove final drive assembly and disassemble it to replace front oil seal and collapsible spacer. Refer to DLN-144, "Removal and Installation" and DLN-160, "Disassembly".
NOTE:

The reuse of collapsible spacer is prohibited in principle. However, it is reusable on a one-time basis only in cases when replacing front oil seal.

Identification stamp of replacement frequency of front oil seal

• The diagonally shaded area in the figure shows stamping point for replacement frequency of front oil seal.

• The following table shows if collapsible spacer replacement is needed before replacing front oil seal.

When collapsible spacer replacement is required, disassemble final drive assembly to replace collapsible spacer and front oil seal.

Refer to DLN-160, "Disassembly".


CAUTION:

CAUTION:
Make a stamping after replacing front oil seal.

• After replacing front oil seal, make a stamping on the stamping point in accordance with the table below in order to identify replacement frequency.

CAUTION:
Make a stamping from left to right.
1. Make a judgment if a collapsible spacer replacement is required.

1. Make a judgment if a collapsible spacer replacement is required. 2. Remove rear propeller shaft. Refer to DLN-121, "Removal and Installation".

3. Measure the total preload with the preload gauge (A) (SST: ST3127S000).

NOTE

:
Record the preload measurement.

4. Put matching mark (B) on the end of the drive pinion. The

4. Put matching mark (B) on the end of the drive pinion. The matching mark (B) should be in line with the matching mark (A) on companion flange (1).

CAUTION:
For matching mark, use paint. Never damage companion flange and drive pinion.
5. Remove companion flange lock nut using the flange wrench (A)

5. Remove companion flange lock nut using the flange wrench (A) (commercial service tool).

6. Remove companion flange using pullers (A) (commercial service

6. Remove companion flange using pullers (A) (commercial service tool).

7. Remove front oil seal using a suitable tool.

CAUTION:
Never damage carrier case.
INSTALLATION

INSTALLATION

1. Apply multi-purpose grease to front oil seal lips.

2. Install front oil seal using the drift (A) (commercial service tool) as shown in figure.

CAUTION:
• Never reuse oil seal.

• Never incline oil seal when installing.

3. Align the matching mark (B) of drive pinion with the matching

3. Align the matching mark (B) of drive pinion with the matching mark (A) of companion flange (1), and then install the companion flange (1).

4. Temporarily tighten drive pinion lock nut to drive pinion, using

4. Temporarily tighten drive pinion lock nut to drive pinion, using flange wrench (commercial service tool).

CAUTION:
• Never reuse drive pinion lock nut.

• Apply anti-corrosion oil to the thread and seat of new drive pinion lock nut.

5. Tighten drive pinion lock nut within the limits of specified torque so as to keep the pinion bearing preload within a standard values, using preload gauge (A) (SST: ST3127S000).

Total preload torque : A value that add 0.1 – 0,4 N·m to the measured value before removing.

CAUTION:
• Adjust to the lower limit of the drive pinion lock nut tightening torque first.

• If the preload torque exceeds the specified value, replace collapsible spacer and tighten it again to adjust. Never loosen drive pinion lock nut to adjust the preload torque.

6. Fit a dial indicator onto the companion flange face (inner side of

6. Fit a dial indicator onto the companion flange face (inner side of the rear propeller shaft mounting bolt holes).

7. Rotate companion flange to check for runout.

Companion flange runout : Refer toDLN-167, "Companion Flange Runout".

8. Fit a test indicator to the inner side of companion flange (socket diameter).

9. Rotate companion flange to check for runout.

Companion flange runout : Refer toDLN-167, "Companion Flange Runout".

10. If the runout value is outside the runout limit, follow the procedure

10. If the runout value is outside the runout limit, follow the procedure below to adjust.

a. Check for runout while changing the phase between companion flange and drive pinion by 90° step, and search for the position where the runout is the minimum. b. If the runout value is still outside of the limit after the phase has been changed, replace companion flange.

c. If the runout value is still outside of the limit after companion flange has been replaced, possible cause will be an assembly malfunction of drive pinion and electric controlled coupling, malfunctioning coupling bearing, or malfunctioning of electric controlled coupling.

11. Make a stamping for identification of front oil seal replacement frequency. Refer to “Identification stamp of replacement frequency of front oil seal”.

CAUTION:
Make a stamping after replacing front oil seal

.

12. Install rear propeller shaft. Refer to DLN-121, "Removal and Installation".

13. Check the final drive for oil leakage. Refer to DLN-132, "Inspection".