Door & Lock type 2

Hood

In this manual: Door & Lock type 2
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

Exploded View

1. Hood assembly

1. Hood assembly
2. Hood bumper rubber
3. Radiator core seal
4. Hood bumper rubber
5. Clamp
6. Hood hinge
7. Grommet
8. Hood support rod

: Pawl: Clip
: Body grease: Pawl
Hood assembly: Body grease


Hood assembly

HOOD ASSEMBLY : Removal and Installation CAUTION:
• Operate with two workers, because of its heavy weight.

• Use protective tape or shop cloth to protect from damage during removal and installation.

REMOVAL

1. Support hood assembly with the proper material to prevent it from falling.

WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood assembly.

2. Remove hood hinge mounting nuts on the hood to remove the hood assembly.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting bolts and nuts.

• After installing, perform hood fitting adjustment. Refer to DLK-305, "HOOD ASSEMBLY : Adjustment".

HOOD ASSEMBLY : Adjustment
1. Hood assembly

1. Hood assembly
2. Hood bumper rubber
3. Hood hinge
4. Hood lock assembly
5. Front bumper fascia
6. Front combination lamp 7. Front fender

: Body grease: N·m (kg-m, ft-lb)
Check the clearance and the surface height between hood and each part by: Body grease


Check the clearance and the surface height between hood and each part by visually and touching.

If the clearance and the surface height are out of specification, adjust them according to the procedures shown below.

FITTING ADJUSTMENT PROCEDURE

FITTING ADJUSTMENT PROCEDURE

1. Remove front center grille. Refer to EXT-18, "Removal and Installation". 2. Remove hood lock assembly, and then adjust the surface height of hood assembly, front fender assembly, and front combination lamp according to the specified value, by rotating hood bumper rubber. 3. Position hood lock assembly and engage hood striker. Check hood lock assembly and hood striker for looseness. 4. Move hood lock assembly laterally until the center of hood striker and hood lock assembly are vertical when viewed from the front. 5. After adjustment, tighten lock bolts to the specified torque. 6. Open hood. Rotate bumper rubber counterclockwise between half a turn and three-quarters of a turn. 7. Check that secondary latch is securely engaged with secondary hood striker from the dead load of the hood assembly.

8. Check that primary latch is securely engaged with primary hood striker when hood assembly is closed [free-fall from approximately 200 mm (7.874 in) height].

CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.

9. Install front center grille. Refer to EXT-18, "Removal and Installation".

Hood hinge

HOOD HINGE : Removal and Installation

REMOVAL

1. Remove hood assembly. Refer to DLK-304, "HOOD ASSEMBLY : Removal and Installation". 2. Remove front fender. Refer to DLK-315, "Removal and Installation".

3. Remove hood hinge mounting bolts, and then remove hood hinge.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• After installation, perform hood hinge fitting adjustment. Refer to DLK-307, "HOOD HINGE : Adjustment". • After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts and nuts.

• Check hood hinge rotating part for poor lubrication. If necessary, apply grease.

HOOD HINGE : Adjustment

HOOD HINGE : Adjustment
1. Hood assembly

1. Hood assembly
2. Hood bumper rubber
3. Hood hinge
4. Hood lock assembly
5. Front bumper fascia
6. Front combination lamp 7. Front fender

: Body grease: N·m (kg-m, ft-lb)
Check the clearance and the surface height between hood and each part by: Body grease


Check the clearance and the surface height between hood and each part by visually and touching.

If the clearance and the surface height are out of specification, adjust them according to the procedures shown below.

1. Remove front center grille. Refer to EXT-18, "Removal and Installation".

1. Remove front center grille. Refer to EXT-18, "Removal and Installation". 2. Remove hood lock assembly. 3. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation". 4. Remove front combination lamp (LH and RH). Refer to EXL-91, "Removal and Installation". 5. Remove front fender assembly (LH and RH). Refer to DLK-315, "Removal and Installation". 6. Loosen hood hinge mounting bolts. 7. Temporarily install front fender assembly (LH and RH), front combination lamp (LH and RH) and front bumper fascia. 8. Adjust the clearance of hood assembly, front fender assembly (LH and RH), front combination lamp (LH and RH) and front bumper fascia according to the specified value, by moving hood hinge (body side). 9. Temporarily tighten hood hinge (LH and RH). 10. Remove front bumper fascia, front combination lamp (LH and RH) and front fender assembly (LH and RH). 11. Tighten hood hinge (LH and RH) to the specified torque. 12. Install front fender assembly (LH and RH). Refer to DLK-315, "Removal and Installation". 13. Install front combination lamp (LH and RH). Refer to EXL-91, "Removal and Installation". 14. Install front bumper fascia. Refer to EXT-13, "Removal and Installation". 15. Adjust the surface height of hood assembly, front fender assembly, and front combination lamp according to the specified value, by rotating hood bumper rubber. 16. Position hood lock assembly and engage hood striker. Check hood lock assembly and hood striker for looseness. 17. Move hood lock assembly laterally until the center of hood striker and hood lock assembly are vertical when viewed from the front. 18. After adjustment, tighten lock bolts to the specified torque. 19. Open hood. Rotate bumper rubber counterclockwise between half a turn and three-quarters of a turn. 20. Check that secondary latch is securely engaged with secondary hood striker from the dead load of the hood assembly.

21. Check that primary latch is securely engaged with primary hood striker when hood assembly is closed [free-fall from approximately 200 mm (7.874 in) height].

CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more

.

22. Install front center grille. Refer to EXT-18, "Removal and Installation".

CAUTION:
After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting bolts and nuts.

Hood support rod

HOOD SUPPORT ROD : Removal and Installation

REMOVAL

CAUTION:
Two workers are required to support the hood.

1. Support hood assembly with a suitable material to prevent it from falling.

WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood assembly.

2. Pull hood support rod from grommet and remove.

INSTALLATION

Install in the reverse order of removal.