Rear Suspension 4WD

Rear shock absorber

In this manual: Rear Suspension 4WD
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Exploded View

1. Suspension arm

1. Suspension arm
2. Shock absorber
3. Bound bumper
4. Bound bumper cover
5. Washer
6. Bushing
7. Distance tube
8. Piston rod lock nut
9. Cap

: Always replace after every: Vehicle front
disassembly.: Always replace after every
disassembly.

Removal and Installation: N·m (kg-m, ft-lb)


Removal and Installation

REMOVAL

1. Remove tires. Refer to WT-7, "Removal and Installation".

2. Set suitable jack under suspension arm.

CAUTION:
• Never damage the suspension arm with a jack.

• Check the stable condition when using a jack.

3. Remove shock absorber mounting bolt and nut (lower side). 4. Remove shock absorber mask. Refer to INT-29, "Exploded View". 5. Remove cap.

6. Remove piston rod lock nut (1), and then remove washer and bushing.

NOTE

:
To loosen piston rod lock nut, fix the tip (A) of the piston rod.

7. Remove shock absorber assembly. 8. Remove bushing, distance tube, bound bumper cover, and bound bumper from shock absorber.

9. Perform inspection after removal. Refer to RSU-24, "Inspection".

INSTALLATION

INSTALLATION

Note the following, and install in the reverse order of removal.

• To install bushings (1), securely insert protrusion (A) into the hole on the vehicle body side.

• Install washer (1) in the direction shown in the figure.

• Install washer (1) in the direction shown in the figure.

: Bushing side

• Perform final tightening of bolts and nuts at the shock absorber lower side (rubber bussing), under unladen conditions with tires on level ground.

• Hold a head (A) of shock absorber piston rod not to have it rotate,

• Hold a head (A) of shock absorber piston rod not to have it rotate, then tighten the piston rod lock nut (1) to the specified torque.

CAUTION:
Never reuse piston rod lock nut.
• When installing the cap, securely engage the cap groove (A) with

• When installing the cap, securely engage the cap groove (A) with the flange on the vehicle side. • Perform inspection after installation. Refer to RSU-24, "Inspection".

• After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber. Refer to RSU-24, "Inspection".

Inspection

Inspection

INSPECTION AFTER REMOVAL

Shock Absorber
Check the following items, and replace the part if necessary.

• Shock absorber for deformation, cracks, and other damage. • Piston rod for damage, uneven wear, and distortion.

• Oil leakage

Bound Bumper, Bushing Check for cracks and damage. Replace it if necessary.

Washer, Bound Bumper Cover, Distance Tube • Check for cracks and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to RSU-20, "Inspection".

Disposal

1. Set shock absorber horizontally to the ground with the piston rod fully extracted.

2. Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position ( as shown in the figure to release gas gradually.) from top
as shown in the figure to release gas gradually.

CAUTION:
• Wear eye protection (safety glass). • Wear gloves.

• Be careful with metal chips or oil blown out by the compressed gas.

NOTE:

• Drill vertically in this direction ( • Directly to the outer tube avoiding brackets.).
• Directly to the outer tube avoiding brackets.

• The gas is clear, colorless, odorless, and harmless.

A : 20 – 30 mm (0.79 – 1.18 in)

A : 20 – 30 mm (0.79 – 1.18 in)

3. Position the drilled hole downward and drain oil by moving the piston rod several times.

CAUTION:
Dispose of drained oil according to the law and local regulations.