SRS Airbag

Side curtain air bag module

In this manual: SRS Airbag
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Exploded View

1. Side curtain air bag module

1. Side curtain air bag module

: N·m (kg-m, ft-lb): Metal clip
Removal and Installation: N·m (kg-m, ft-lb)


Removal and Installation

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more. • Always work from the side of curtain air bag module. Never work in front of it.

• Never use the air tools or electric tools for servicing.

REMOVAL

1. Remove headlining assembly. Refer to INT-26, "Removal and Installation". 2. Remove the curtain air bag module mounting bolt that is located on the front pillar.

3. Disengage metal clips on the front roof.

1. Fully insert a flat-bladed screwdriver (A) into center of metal clip.

1. Fully insert a flat-bladed screwdriver (A) into center of metal clip. 2. Lift the flat-bladed screwdriver upward as shown in the figure and disengage upper side of metal clip.

3. Rotate the flat-bladed screwdriver as shown in the figure and disengage lower side of metal clip.

CAUTION:: Metal clip


CAUTION:
Never deform metal clip.

4. Disconnect side curtain air bag harness connector.

CAUTION:
• For installing/removing the side curtain air bag harness connector, insert thin screwdriver wrapped in tape into notch, lift lock and remove the connector. • Install the connector with lock raised, and push lock into the connector.

• After installing the connector, check that the lock is pushed securely into it.

5. Remove the curtain air bag module mounting bolts that are located on the

5. Remove the curtain air bag module mounting bolts that are located on the rear pillar. 6. Remove the curtain air bag module mounting bolts that are located on the center pillar.

7. Remove the curtain air bag module mounting bolts that are located on the inflator, and then remove curtain air bag module.

CAUTION:
• Never impact the side curtain air bag module.

• Replace the side curtain air bag module if it has been dropped or sustained an impact.

• Never insert any foreign objects (screwdriver, etc.) into the side

• Never insert any foreign objects (screwdriver, etc.) into the side curtain air bag module. • Never disassemble the side curtain air bag module. • Never expose the side curtain air bag module to temperatures exceeding 90 °C.

• Never allow oil, grease, detergent, or water to come in contact with the side curtain air bag module

.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• Insert metal clips of front roof until a locking sound is heard. Pull metal clips and check that it is fully locked to the vehicle body. • Check perforation of curtain air bag module to check that curtain air bag module is not twisted. • Never damage the harness while installing. • If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunctioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-12, "On Board Diagnosis Function" or SRC-16, "CONSULT-III Function".

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.