SRS Airbag

Disposal of air bag module

In this manual: SRS Airbag
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~17min read

Driver air bag module : Deployment

CHECKING DEPLOYMENT TOOL

Connecting to Battery CAUTION:
The battery must show voltage of 9.6 V or more.

Remove the battery from the vehicle and place it on dry wood blocks approximately 5.0 m (16.4 ft) away from the vehicle.

• Wait 3 minutes after the vehicle battery is disconnected before proceeding.

• Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal.

Check that the polarity is correct. The right side lamp in the tool, marked “deployment tool power”, should illuminate with a green light. If the right side lamp illuminates red, reverse the connections to the battery.

Deployment Tool Check

Deployment Tool Check Press the deployment tool switch (C) to the ON position. The left side lamp in the tool, marked “air bag connector voltage” should illuminate (B). If it does not illuminate, replace the deployment tool (A).

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

*: If this lamp illuminates red, the tool is connected to the battery

*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illuminates green.

DEPLOYMENT OF DRIVER AIR BAG MODULE (OUTSIDE OF VEHICLE)

1. Unless the vehicle is being scrapped, deploying the air bag in the vehicle is not recommended. This may cause damage to the vehicle interior.

Anchor air bag module bracket (SST: KV99105300) (A) in a vice secured to a firm foundation deployment.

2. Using wire (D), secure driver air bag module (1) to air bag module

2. Using wire (D), secure driver air bag module (1) to air bag module bracket (SST: KV99105300) (A) at two places.

CAUTION:
Use wire of at least 1.0 mm (0.039 in) diameter.
3. Firmly secure air bag module bracket (SST: KV99105300) with driver air bag module attached, in a vise.

4. Connect deployment tool adapter (SST: KV99110500) (C) to driver air bag module and deployment tool connector (SST: KV99106400) (B).

5. Connect red clip of deployment tool (A) to battery positive terminal

5. Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal (B). 6. The lamp on the right side of the tool, marked “deployment tool power”, should illuminate green, not red.

7. Press the button on the deployment tool. The left side lamp on the tool, marked “air bag connector voltage”, illuminates and the air bag module (1) deploys.

CAUTION:
When deploying the driver air bag module, stand at least 5.0 m (16.4 ft) away from the air bag module.
Driver air bag module : Disposal

Driver air bag module : Disposal

DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal.

CAUTION:
• Never apply water to a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner. • Wear gloves when handling a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner.

• No poisonous gas is produced upon air bag module deployment.

However, be careful not to inhale gas since it irritates the throat and can cause choking. • Never disassemble air bag module, seat belt pre-tensioner and lap pre-tensioner. • Air bag module, seat belt pre-tensioner and lap pre-tensioner cannot be reused.

• Wash your hands clean after the work is complete.

Front passenger air bag module : Deploy

Front passenger air bag module : Deploy

CHECKING DEPLOYMENT TOOL

Connecting to Battery CAUTION:
The battery must show voltage of 9.6 V or more.

Remove the battery from the vehicle and place it on dry wood blocks approximately 5.0 m (16.4 ft) away from the vehicle.

• Wait 3 minutes after the vehicle battery is disconnected before proceeding.

• Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal.

Check that the polarity is correct. The right side lamp in the tool, marked “deployment tool power”, should illuminate with a green light. If the right side lamp illuminates red, reverse the connections to the battery.

Deployment Tool Check

Deployment Tool Check Press the deployment tool switch (C) to the ON position. The left side lamp in the tool, marked “air bag connector voltage” should illuminate (B). If it does not illuminate, replace the deployment tool (A

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

*: If this lamp illuminates red, the tool is connected to the battery

*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illuminates green.

DEPLOYMENT OF FRONT PASSENGER AIR BAG MODULE (OUTSIDE OF VEHICLE)

1. Remove the front passenger air bag module (1) from lid (2) with remover tool (A).

2. Make 8.5 mm (0.335 in) diameter hole (B) in air bag module

2. Make 8.5 mm (0.335 in) diameter hole (B) in air bag module bracket (SST: KV99105300) (A) at the position shown in figure.

3. Firmly secure air bag module bracket (SST: KV99105300) (A) in

3. Firmly secure air bag module bracket (SST: KV99105300) (A) in a vise. 4. Insert two bolts (D) through air bag module bracket and front passenger air bag module (1) lower side holes, and fix then with two nuts.

5. Connect deployment tool (SST: KV99106400) (B) and deployment tool adapter (SST: KV99110500) (C) to front passenger air bag module.

6. Connect red clip of deployment tool (A) to battery positive terminal

6. Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal (B). 7. The lamp on the right side of the tool, marked “deployment tool power”, should illuminate green, not red.

8. Press the button on the deployment tool (A). The left side lamp on the tool, marked “air bag connector voltage”, illuminates and the front passenger air bag module (1) deploys.

CAUTION:
• When deploying the front passenger air bag module, never stand on the deploying side.

• Stand at least 5.0 m (16.4 ft) away from the front passenger air bag module.

Front passenger air bag module : Disp

Front passenger air bag module : Disp

DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal.

CAUTION:
• Never apply water to a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner. • Wear gloves when handling a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner.

• No poisonous gas is produced upon air bag module deployment.

However, be careful not to inhale gas since it irritates the throat and can cause choking. • Never disassemble air bag module, seat belt pre-tensioner and lap pre-tensioner. • Air bag module, seat belt pre-tensioner and lap pre-tensioner cannot be reused.

• Wash your hands clean after the work is complete.

Front side air bag module : Deployment

Front side air bag module : Deployment

CHECKING DEPLOYMENT TOOL

Connecting to Battery CAUTION:
The battery must show voltage of 9.6 V or more.

Remove the battery from the vehicle and place it on dry wood blocks approximately 5.0 m (16.4 ft) away from the vehicle.

• Wait 3 minutes after the vehicle battery is disconnected before proceeding.

• Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal.

Check that the polarity is correct. The right side lamp in the tool, marked “deployment tool power”, should illuminate with a green light. If the right side lamp illuminates red, reverse the connections to the battery.

Deployment Tool Check

Deployment Tool Check Press the deployment tool switch (C) to the ON position. The left side lamp in the tool, marked “air bag connector voltage” should illuminate (B). If it does not illuminate, replace the deployment tool (A).

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

*: If this lamp illuminates red, the tool is connected to the battery

*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illuminates green.

DEPLOYMENT OF FRONT SIDE AIR BAG MODULE (OUTSIDE OF VEHICLE)

1. Make 6.5 mm (0.256 in) diameter hole (B) in air bag module bracket (SST: KV99105300) (A) at the position shown in figure.

2. Firmly secure air bag module bracket (SST: KV99105300) in a

2. Firmly secure air bag module bracket (SST: KV99105300) in a vise. 3. Insert two bolts through air bag module bracket and front side air bag module (1) upper side holes, and fix them with two nuts (C).

4. Connect deployment tool (SST: KV99106400) (A) and deployment tool adapter (SST: KV99108300) (B) to front side air bag module connector.

5. Connect red clip of deployment tool (SST: KV99106400) (A) to

5. Connect red clip of deployment tool (SST: KV99106400) (A) to battery positive terminal and black clip to negative terminal (B). 6. The lamp on the right side of the tool, marked “deployment tool power”, should illuminate green, not red.

7. Press the button on the deployment tool. The left side lamp on the tool, marked “air bag connector voltage”, illuminates and the air bag module (1) deploys.

CAUTION:
When deploying the front side air bag module, stand at least 5.0 m (16.4 ft) away from the front side air bag module.
Front side air bag module : Disposal

Front side air bag module : Disposal

DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal.

CAUTION:
• Never apply water to a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner. • Wear gloves when handling a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner.

• No poisonous gas is produced upon air bag module deployment.

However, be careful not to inhale gas since it irritates the throat and can cause choking. • Never disassemble air bag module, seat belt pre-tensioner and lap pre-tensioner. • Air bag module, seat belt pre-tensioner and lap pre-tensioner cannot be reused.

• Wash your hands clean after the work is complete.

Side curtain air bag module : Deployment

Side curtain air bag module : Deployment

CHECKING DEPLOYMENT TOOL

Connecting to Battery CAUTION:
The battery must show voltage of 9.6 V or more.

Remove the battery from the vehicle and place it on dry wood blocks approximately 5.0 m (16.4 ft) away from the vehicle.

• Wait 3 minutes after the vehicle battery is disconnected before proceeding.

• Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal.

Check that the polarity is correct. The right side lamp in the tool, marked “deployment tool power”, should illuminate with a green light. If the right side lamp illuminates red, reverse the connections to the battery.

Deployment Tool Check

Deployment Tool Check Press the deployment tool switch (C) to the ON position. The left side lamp in the tool, marked “air bag connector voltage” should illuminate (B). If it does not illuminate, replace the deployment tool (A).

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

*: If this lamp illuminates red, the tool is connected to the battery

*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illuminates green.

DEPLOYMENT OF SIDE CURTAIN AIR BAG MODULE (OUTSIDE OF VEHICLE)

1. Cut off the bands (1).

2. Cut the inflator (3) from side curtain air bag module (2).

3. Connect deployment tool (SST: KV99106400) (A) and deployment

3. Connect deployment tool (SST: KV99106400) (A) and deployment tool adapter (SST: KV99110500) (B) to the inflator (1).

4. Put the inflator (1) connected with the deployment tool (A) (SST:

4. Put the inflator (1) connected with the deployment tool (A) (SST: KV99106400) and deployment tool adapter (B) (SST: KV99110500) into a tire without a wheel (C).

5. Put the tire with the inflator (1) onto another tire without a wheel.

5. Put the tire with the inflator (1) onto another tire without a wheel.

Add an additional tire without a wheel and then a tire mounted on a wheel on top.

CAUTION:
Tie all tires together with a strap in order keep them standing. 6. Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal. 7. The lamp on the right side of the tool, marked “deployment tool power”, should illuminate green, not red.

8. Press the button on the deployment tool. The left side lamp on the tool, marked “air bag connector voltage”, illuminates and the air bag module inflator deploys.

CAUTION:
When deploying the side curtain air bag module, stand at least 5.0 m (16.4 ft) away from the side curtain air bag module.
Side curtain air bag module : Disposal

Side curtain air bag module : Disposal

DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal.

CAUTION:
• Never apply water to a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner. • Wear gloves when handling a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner.

• No poisonous gas is produced upon air bag module deployment.

However, be careful not to inhale gas since it irritates the throat and can cause choking. • Never disassemble air bag module, seat belt pre-tensioner and lap pre-tensioner. • Air bag module, seat belt pre-tensioner and lap pre-tensioner cannot be reused.

• Wash your hands clean after the work is complete.

Seat belt pre-tensioner : Deplo

Seat belt pre-tensioner : Deplo

CHECKING DEPLOYMENT TOOL

Connecting to Battery CAUTION:
The battery must show voltage of 9.6 V or more.

Remove the battery from the vehicle and place it on dry wood blocks approximately 5.0 m (16.4 ft) away from the vehicle.

• Wait 3 minutes after the vehicle battery is disconnected before proceeding.

• Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal.

Check that the polarity is correct. The right side lamp in the tool, marked “deployment tool power”, should illuminate with a green light. If the right side lamp illuminates red, reverse the connections to the battery.

Deployment Tool Check

Deployment Tool Check Press the deployment tool switch (C) to the ON position. The left side lamp in the tool, marked “air bag connector voltage” should illuminate (B). If it does not illuminate, replace the deployment tool (A).

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

*: If this lamp illuminates red, the tool is connected to the battery

*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illuminates green.

DEPLOYMENT OF FRONT SEAT BELT PRE-TENSIONER (OUTSIDE OF VEHICLE)

1. Firmly grip pre-tensioner (1) in a vise (A) and cut off the webbing.

2. Connect deployment tool (SST: KV99106400) (A) and deployment

2. Connect deployment tool (SST: KV99106400) (A) and deployment tool adapter (SST: KV99110500) (B) yellow connector to front seat belt pre-tensioner (1). 3. Connect red clip of deployment tool to battery positive terminal and black clip to negative terminal (C). 4. The lamp on the right side of the tool, marked “deployment tool power”, should illuminate green, not red.

5. Press the button on the deployment tool. The left side lamp on the tool, marked “seat belt pre-tensioner connector voltage”, illuminates and the front seat belt pre-tensioner deploys.

CAUTION:
When deploying the front seat belt pre-tensioner, stand at least 5.0 m(16.4 ft) away from the front seat belt pre-tensioner.
Seat belt pre-tensioner : Disposal

Seat belt pre-tensioner : Disposal

DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal.

CAUTION:
• Never apply water to a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner. • Wear gloves when handling a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner.

• No poisonous gas is produced upon air bag module deployment.

However, be careful not to inhale gas since it irritates the throat and can cause choking. • Never disassemble air bag module, seat belt pre-tensioner and lap pre-tensioner. • Air bag module, seat belt pre-tensioner and lap pre-tensioner cannot be reused.

• Wash your hands clean after the work is complete.

Lap pre-tensioner : Deployment

Lap pre-tensioner : Deployment

CHECKING DEPLOYMENT TOOL

Connecting to Battery CAUTION:
The battery must show voltage of 9.6 V or more.

Remove the battery from the vehicle and place it on dry wood blocks approximately 5.0 m (16.4 ft) away from the vehicle.

• Wait 3 minutes after the vehicle battery is disconnected before proceeding.

• Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal.

Check that the polarity is correct. The right side lamp in the tool, marked “deployment tool power”, should illuminate with a green light. If the right side lamp illuminates red, reverse the connections to the battery.

Deployment Tool Check

Deployment Tool Check Press the deployment tool switch (C) to the ON position. The left side lamp in the tool, marked “air bag connector voltage” should illuminate (B). If it does not illuminate, replace the deployment tool (A).

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)

*: If this lamp illuminates red, the tool is connected to the battery

*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illuminates green.

DEPLOYMENT OF LAP PRE-TENSIONER (OUTSIDE OF VEHICLE)

1. Remove lap pre-tensioner (1). Refer to SB-5, "SEAT BELT RETRACTOR : Removal and Installation".

2. Connect deployment tool (SST: KV99106400) (A) and deployment

2. Connect deployment tool (SST: KV99106400) (A) and deployment tool adapter (SST: KV99110500) (B) orange connector to lap pre-tensioner (1).

3. Put the lap pre-tensioner (1) connected with the deployment tool

3. Put the lap pre-tensioner (1) connected with the deployment tool into a tire without a wheel.

4. Connect red clip of deployment tool (A) to battery positive terminal

4. Connect red clip of deployment tool (A) to battery positive terminal and black clip to negative terminal. 5. The lamp on the right side of the tool, marked “deployment tool power”, should glow green, not red.

6. Press the button on the deployment tool. The left side lamp on the tool, marked “lap pre-tensioner connector voltage”, will illuminate and the lap pre-tensioner (1) will deploy.

CAUTION:
When deploying the lap pre-tensioner, stand at least 5.0 m (16.4 ft) away from the lap pre-tensioner.
Lap pre-tensioner : Disposal

Lap pre-tensioner : Disposal

DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal.

CAUTION:
• Never apply water to a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner. • Wear gloves when handling a deployed air bag module or seat belt pre-tensioner or lap pre-tensioner.

• No poisonous gas is produced upon air bag module deployment.

However, be careful not to inhale gas since it irritates the throat and can cause choking. • Never disassemble air bag module, seat belt pre-tensioner and lap pre-tensioner. • Air bag module, seat belt pre-tensioner and lap pre-tensioner cannot be reused.

• Wash your hands clean after the work is complete.

SRS Airbag Control System