Driver Information & Multimedia

B1341 Head Unit

18steps
~108min
4/5difficulty
Done 0 of 18
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B1341–16

Head unit

(Audio unit)
[VB–LOW] Diagnosis condition When ignition switch is ON.
Signal (terminal) –
Threshold –
Diagnosis delay time 30 seconds or more
B1341–17 [VB–HIGH] Diagnosis condition When ignition switch is ON.
Signal (terminal) –
Threshold –
Diagnosis delay time 30 seconds or more
B1341–49 [—] Diagnosis condition When ignition switch is ON.
Signal (terminal) –
Threshold –
Diagnosis delay time 30 seconds or more
B1341–55 [CONFIG] Diagnosis condition When ignition switch is ON.
Signal (terminal) –
Threshold –
Diagnosis delay time 30 seconds or more
B1341–98 [TEMP] Diagnosis condition When ignition switch is ON.
Signal (terminal) –
Threshold –
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

  • Charging system malfunction

  • Audio unit configuration

  • Audio unit

FAIL-SAFE

  • Failure type byte 16: battery protection shuts Audio unit down 60 seconds after low voltage condition

  • Failure type byte 17:

    • Audio unit display inoperative

    • Audio output is inoperative

  • Failure type byte 49: Audio unit internal failure

  • Failure type byte 55: Audio unit configuration error

  • Failure type byte 98: Audio unit shuts down after 5 seconds

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “MULTI AV”.

  5. Check DTC.

Is DTC B1341 detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

DETERMINE MALFUNCTION TYPE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “MULTI AV”.

  5. Check DTC.

Is DTC B1341–16, 17, 49, 55 or 98 detected?

YES>>

16 [VB–LOW], or 17 [VB–HIGH] – GO TO 2.

YES>>

49 [—] – GO TO 4.

YES>>

55 [CONFIG] – GO TO 3.

YES>>

98 [TEMP] – GO TO 5.

NO>>

Refer to Intermittent Incident.

CHECK BATTERY VOLTAGE

Check 12­volt battery voltage.

Is 12­volt battery voltage less than 8.8V?

YES>>

Charge battery and retest. Refer to Work Flow (With 165-DSS-5000P), or (Without 165-DSS-5000P).

NO>>

Replace audio unit. Refer to Removal and Installation.

PERFORM CONFIGURATION PROCEDURE

Perform configuration of audio unit. Refer to Work Procedure.

>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC B1341–49 or B1341–55 detected again?

YES>>

Replace audio unit. Refer to Removal and Installation.

NO>>

Inspection End.

CHECK AUDIO UNIT

Visually check around audio unit for a cause of high temperature.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Remove cause of high temperature.

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “MULTI AV”.

  5. Check DTC.

Is DTC B1341–98 detected?

YES>>

Replace audio unit. Refer to Removal and Installation.

NO>>

Inspection End.