Distance Sensor (icc Sensor) Alignment
Always perform the radar alignment after removing and installing or replacing the distance sensor.
Application Notice
| Type | Description |
|---|---|
| TYPE 1 | When using KV99112700 for radar alignment. Refer to Description. |
| TYPE 2 | When using 1-20-2851-1 for radar alignment. Refer to Description. |
TYPE 1
Description
A 4-wheel vehicle alignment must be performed before proceeding with radar alignment procedure.
Always perform the radar alignment after removing and installing or replacing the distance sensor.
Set the target board (SST: KV99112700) to the correct position in front of the vehicle.
Set the radar alignment mode (“MILLIWAVE RADAR ADJUST” on “Work support”) with CONSULT, and then perform the adjustment according to the display. (Distance sensor automatically adjusts.)
Preparation
ADVANCE PREPARATION FOR RADAR ALIGNMENT
Adjust all tire pressure to the specified value.
Empty the Nissan Murano vehicle. (Remove any luggage from the passenger compartment, trunk room, etc.)
Shift the selector lever to “P” position, and release the parking brake.
Fully fill the fuel tank, and then check that the coolant and oils are filled up to correct level.
Clean the distance sensor area
of the front bumper grille.
GO TO 2.
RADAR ALIGNMENT OPERATION AREA
Position the Nissan Murano vehicle in a place that is level and where
area can be secured.

| W | : 3000 mm (118.11 in) |
| L | : 2000 mm (78.74 in) |
| H | : 2000 mm (78.74 in) |
Go to Setting The Target Board.
Setting The Target Board
Accurate adjustment of the radar alignment requires that the target board be accurately positioned.
TARGET BOARD HEIGHT ADJUSTMENT
Adjust the base of target board to approximately 30 mm (1.18 in) from the ground.
>>GO TO 2.
PREPARATION OF SETTING TARGET BOARD (1)

| “A”–“E” (“C”–“F”) | : 2100 mm (82.6 in) |
Mark points “A”, “B”, “C” and “D”at the center of the lateral surface of each wheels.

Draw line “LH” passing through points “A” and “B” on the left side of Nissan Murano vehicle.
Mark point “E” on the line “LH” at the positions 2100 mm (82.6 in) from point “A”.
Draw line “RH” passing through points “C” and “D” on the right side of Nissan Murano vehicle in the same way as step 2.
Mark point “F” on the line “RH” at the positions 2100 mm (82.6 in) from point “C”.
Draw line “FW” passing through the points “E” and “F” on the front side of Nissan Murano vehicle.
Mark point “X” at the center of point “E” and “F” on the line “FW”.
GO TO 3.
SETTING TARGET BOARD
Place the center of target board on point “G” at line “E-F” and install the target board.

| L1 | : 2100 mm (82.6 in) |
| L2 | : 0 mm (0 in) |
GO TO 4.
CHECK THE TARGET BOARD INSTALLATION AREA
Do not place anything other than target board in the space shown in the figure (view from top).

| No object zone | Distance sensor | Target board | |||
| W. | 3000 mm (118.11 in) | L. | 1500 mm (59.06 in) |
Go to Radar Alignment.
Radar Alignment
The radar alignment is performed automatically with CONSULT.
PERFORM RADAR ALIGNMENT
Start the engine.
Connect CONSULT and select “Work support” of “LASER/RADAR”.
Select “MILLIWAVE RADAR ADJUST”.
The target should be accurately placed.
The Nissan Murano vehicle should be stopped.
Select “Start” after the conditions displayed on CONSULT are satisfied.
Select “Next” after the “Radar alignment conditions are ready.” screen is displayed.
Confirm the displayed item.
“Completed.”: Go to 7.
Except “Completed.”: Perform the following services.
Displayed item Possible cause Service procedure Alignment result is over threshold. DTC is detected
The position of the target board is incorrect
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again Horizontal value is over threshold.
Check the condition.
Perform the adjust again.DTC is detected
The position of the target board is shifted horizontally
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again Vertical value is over threshold.
Check the condition.
Perform the adjust again.DTC is detected
The position of the target board is shifted vertically
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again Horizontal value and Vertical value are over threshold.
Check the condition.
Perform the adjust again.DTC is detected
The position of the target board is shifted horizontally and vertically
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again This display direction is looking from driver seat side. Target is not detected. (Reflection radio waves is weak.)
Reconfirm the placing condition, and then re-perform adjustment.A target is not-yet -placed
The position of the target board is incorrect
The position of the distance sensor is incorrect
Check the Nissan Murano vehicle alignment condition and perform radar alignment again Target setting is offset in horizontal direction.
Reconfirm the placing condition. And then re-perform adjustment or re-install the radar.The position of the target board is shifted horizontally
The position of the distance sensor is shifted horizontally
Check the Nissan Murano vehicle alignment condition and perform radar alignment again Target setting is offset in vertical direction.
Reconfirm the placing condition. And then re-perform adjustment or re-install the radar.The position of the target board is shifted vertically
The position of the distance sensor is shifted vertically
Check the Nissan Murano vehicle alignment condition and perform radar alignment again EEPROM writing is error.
Re-perform adjustment or replace the ECU.The condition of the alignment is incorrect
Distance sensor malfunction
Check the Nissan Murano vehicle alignment condition and perform radar alignment again
If same massage displays again, replace the distance sensor
Hardware is imperfect.
Replace the ECU.Distance sensor hardware has trouble for alignment Replace the distance sensor Signal of Nissan Murano vehicle side is imperfect or combination of ECU is incorrect.
Diagnose the other ECU.Other ECU except distance sensor have trouble for alignment Check if any DTC is detected in “Self Diagnostic Result” of other ECU except distance sensor
If any DTC is not detected, replace the distance sensor
Software is incorrect.
Replace the ECU.Distance sensor software is incorrect Replace the distance sensor
Confirm displayed value.
Displayed item Monitor item Reference value Completed Vertical Angle Radar angle “DownW” or “UpW” Vertical Angle Radar measurement result (- 2.50) - (+ 3.00) Horizontal Angle Radar angle “LeftW” or “RightW” Horizontal Angle Radar measurement result Less than 0 ± 4.00 deg Alignment status Alignment complete Within reference value: Go to 8.
Outside of reference value: Check the target board condition and perform radar alignment again.
Select “End”.
RADAR ALIGNMENT END
TYPE 2
Description
A 4-wheel vehicle alignment must be performed before proceeding with radar alignment procedure.
Always perform the radar alignment after removing and installing or replacing the distance sensor.
Always perform the radar alignment if rear axle toe settings have been made.
Required tools, refer to Required Tools.
Preparation, refer to Preparation.
Nissan Murano Vehicle set up, refer to Vehicle Set Up.
Setting the target board, refer to Setting The Target Board.
Distance sensor adjustment, refer to distance Sensor Adjustment.
Required Tools
The following tools are necessary to perform distance sensor alignment:
Radar Sensor Aiming Kit 1–20–2851–1 Kit includes the following:
a) Target Board (Fixture)
b) Laser assembly
c) Rear Stand
Use kit 1–20–2851–1 with a self-centering wheel adapter (e.g. 1–20–2722–1–IF, Hunter 20–3339–1 or equivalent).
Target board.

: Position 1, with top tilted 2° toward Nissan Murano vehicle (Not used).
: Position 2, vertical.
: Position 3, with top tilted 2° away from Nissan Murano vehicle (Not used).
Hunter self-centering wheel adapter
[shown with laser assembly
installed] (Hunter alignment rack head may be substituted).
Laser assembly (with bi-directional laser beam) as shown in the illustration.

Tightening knob

Power ON/OFF button

Front laser beam opening

Rear laser beam opening

Attaching shaft

Rear stand as shown in the illustration.

Rear stand

Laser signal reception plate

Distance chain (not shown)
Preparation
ADVANCE PREPARATION FOR RADAR ALIGNMENT PROCEDURE
Adjust all tire pressure to the specified value.
Empty the Nissan Murano vehicle. (Remove any luggage from the passenger compartment, luggage room, etc.)
Shift the selector lever to “P” position, and release the parking brake.
Fully fill the fuel tank, and then check that the coolant and oils are filled up to correct level.
Clean the distance sensor area
of the front bumper grille.
Refer to Nissan Murano Vehicle Set Up.
Vehicle Set Up
Accurate adjustment of the radar alignment requires that the target board, wheel adapter, laser assembly, and rear stand be properly positioned.
PREPOSITION TARGET BOARD
To identify the sensor wave axis center, measure the point
as shown in the illustration.
A : 0 mm (0 in) B : 397.8 mm (15.66 in) C : Nissan Murano Vehicle center Target board setting must be in the center position. (Position 2)
Attaching the distance sensor alignment kit attachment board to the target board.
Position the target board in front facing the right front side of the Nissan Murano vehicle:

Place the marked center of the target board
397.8 mm (15.66 in) ± 50 mm (1.97 in) facing the distance sensor.Adjust the height of the target board using the adjustable nut
to achieve the proper height. The up/down tolerance is ± 30 mm (1.18 in).Adjust the target board lateral position aligning the marked center of the board horizontally with the center of the distance sensor. The right/left tolerance is ± 80 mm (3.15 in).
Extend the machined arm of the target board exposing the reflective surface
to the right front side of the Nissan Murano vehicle.Place one side of the laser assembly
flush against the center of the target board
to assist in the positioning.
Turn the laser assembly ON
allowing the laser beam to emit through the opening of the laser assembly toward the center of the distance sensor.Move the target board
as necessary so that center of target board aligns with center of distance sensor.Turn the laser assembly OFF when done.
Are using Hunter alignment equipment?
YES>>Refer to Hunter’s equipment instructions for complete Nissan Murano vehicle set up and target board setting. Then, refer to Distance Sensor Adjustment.
NO>>GO TO 2.
INSTALLING LASER ASSEMBLY
Install the wheel adapter
on the right front wheel.
Mount the laser assembly
to the wheel adapter
as shown in the figure.
GO TO 3.
SETTING UP REAR STAND
Place the rear stand next to the right rear tire as shown in the figure.

Turn the laser assembly ON allowing the laser beam to be emitted through the front and rear laser assembly openings.
Measure and record the distance (Dr) between the edge of the right rear wheel and the laser beam
on the rear stand (horizontal line).Measure and record the height (Hr) between the laser beam
on the rear stand and ground level (vertical line).Measure and record the distance (Df) between the edge of the right front wheel and the laser beam signal/opening
on the laser assembly (horizontal line).
Measure and record the height (Hf) between the laser beam signal/opening
on the laser assembly and ground level (vertical line).Adjust laser beam as necessary until the two distances match and the two heights match.
Refer to Setting The Target Board.
Setting The Target Board
Accurate adjustment of the radar alignment requires that the target board be accurately positioned.
TARGET BOARD FINAL SETTING
With the target board arm extended, the laser beam
emitted by the laser assembly
will be reflected back
toward the laser assembly.
Rotate the target board to achieve the necessary horizontal adjustment.
Adjust the target board leveling screws to achieve the necessary vertical adjustment.
The figure shown illustrates the laser beam
emitted by the laser assembly
and its reflection
off of the target board arm.
GO TO 2.
CHECK THE POSITION OF THE TARGET BOARD
Do not place anything other than the target board in the space shown in front of the Nissan Murano vehicle (view from top).

| Target board arm | Target board | Distance sensor | |||
| Nissan Murano Vehicle | |||||
| Distance between front wheel and laser beam (Df) | Distance between rear wheel and laser beam (Dr) | Height between front laser beam and ground (Hf) | |||
| Height between rear laser beam and ground (Hr) | Target board center position | 1010 - 1110 mm (39.76 - 43.7 in) |
Refer to Distance Sensor Adjustment.
Distance Sensor Adjustment
The radar alignment is performed automatically with CONSULT.
PERFORM RADAR ALIGNMENT
Start the engine.
Connect CONSULT and select “Work support” of “LASER/RADAR”.
Select “MILLIWAVE RADAR ADJUST”.
The target should be accurately placed.
The Nissan Murano vehicle should be stopped.
Select “Start” after the conditions displayed on CONSULT are satisfied.
Select “Next” after the “Radar alignment conditions are ready.” screen is displayed.
Confirm the displayed item.
“Completed.”: Go to 7.
Except “Completed.”: Perform the following services.
Displayed item Possible cause Service procedure Alignment result is over threshold. DTC is detected
The position of the target board is incorrect
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again Horizontal value is over threshold.
Check the condition.
Perform the adjust again.DTC is detected
The position of the target board is shifted horizontally
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again Vertical value is over threshold.
Check the condition.
Perform the adjust again.DTC is detected
The position of the target board is shifted vertically
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again Horizontal value and Vertical value are over threshold.
Check the condition.
Perform the adjust again.DTC is detected
The position of the target board is shifted horizontally and vertically
Nissan Murano Vehicle is moving
Check the vehicle alignment condition and perform radar alignment again This display direction is looking from driver seat side. Target is not detected. (Reflection radio waves is weak.)
Reconfirm the placing condition, and then re-perform adjustment.A target is not-yet -placed
The position of the target board is incorrect
The position of the distance sensor is incorrect
Check the Nissan Murano vehicle alignment condition and perform radar alignment again Target setting is offset in horizontal direction.
Reconfirm the placing condition. And then re-perform adjustment or re-install the radar.The position of the target board is shifted horizontally
The position of the distance sensor is shifted horizontally
Check the Nissan Murano vehicle alignment condition and perform radar alignment again Target setting is offset in vertical direction.
Reconfirm the placing condition. And then re-perform adjustment or re-install the radar.The position of the target board is shifted vertically
The position of the distance sensor is shifted vertically
Check the Nissan Murano vehicle alignment condition and perform radar alignment again EEPROM writing is error.
Re-perform adjustment or replace the ECU.The condition of the alignment is incorrect
Distance sensor malfunction
Check the Nissan Murano vehicle alignment condition and perform radar alignment again
If same massage displays again, replace the distance sensor
Hardware is imperfect.
Replace the ECU.Distance sensor hardware has trouble for alignment Replace the distance sensor Signal of Nissan Murano vehicle side is imperfect or combination of ECU is incorrect.
Diagnose the other ECU.Other ECU except distance sensor have trouble for alignment Check if any DTC is detected in “Self Diagnostic Result” of other ECU except distance sensor
If any DTC is not detected, replace the distance sensor
Software is incorrect.
Replace the ECU.Distance sensor software is incorrect Replace the distance sensor
Confirm displayed value.
Displayed item Monitor item Reference value Completed Vertical Angle Radar angle “DownW” or “UpW” Vertical Angle Radar measurement result (- 2.50) - (+ 3.00) Horizontal Angle Radar angle “LeftW” or “RightW” Horizontal Angle Radar measurement result Less than 0 ± 4.00 deg Alignment status Alignment complete Within reference value: Go to 8.
Outside of reference value: Check the target board condition and perform radar alignment again.
Select “End”.
RADAR ALIGNMENT END