LIN Communication Bus Malfunction (B2325)

DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors and sliding roof ECU (sliding roof drive gear sub-assembly)*. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors and sliding roof ECU (sliding roof drive gear sub-assembly)* is detected consecutively 3 times.

• *: w/ Sliding Roof System

DTC Code	DTC Detection Condition	Trouble Area
B2325	The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof ECU (sliding roof drive gear sub-assembly)* consecutively 3 times.	Multiplex network master switch assembly Front power window regulator motor assembly LH Front power window regulator motor assembly RH Rear power window regulator motor assembly LH Rear power window regulator motor assembly RH Multiplex network door ECU (back door P/W) Sliding roof ECU (sliding roof drive gear sub-assembly)* Driver side junction block assembly Main body ECU (multiplex network body ECU) Harness or connector

• *: w/ Sliding Roof System

WIRING DIAGRAM
CAUTION / NOTICE / HINT

NOTICE:

• When using the Techstream with the ignition switch off to troubleshoot:

  Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

• Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.

PROCEDURE

1. CLEAR DTC

(a) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

OK:

DTC B2325 is not output.

OK

USE SIMULATION METHOD TO CHECK

NG

1. CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
A-16 (LIN2) - 2B-11	Always	Below 1 Ω
A-16 (LIN2) or 2B-11 - Body ground	Always	10 kΩ or higher

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

OK

1. CLEAR DTC

(a) Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (See page ).

(b) Disconnect the I2 front power window regulator motor assembly LH connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output	A
DTC B2325 is not output	B

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

A

1. CLEAR DTC

(a) Connect the I2 front power window regulator motor assembly LH connector.

(b) Disconnect the h1 multiplex network master switch assembly connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output	A
DTC B2325 is not output	B

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

A

1. CLEAR DTC

(a) Connect the h1 multiplex network master switch assembly connector.

(b) Disconnect the H2 front power window regulator motor assembly RH connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output	A
DTC B2325 is not output	B

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

A

1. CLEAR DTC

(a) Connect the H2 front power window regulator motor assembly RH connector.

(b) Disconnect the J2 rear power window regulator motor assembly RH connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output	A
DTC B2325 is not output	B

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

A

1. CLEAR DTC

(a) Connect the J2 rear power window regulator motor assembly RH connector.

(b) Disconnect the K2 rear power window regulator motor assembly LH connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output	A
DTC B2325 is not output	B

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

A

1. CLEAR DTC

(a) Connect the K2 rear power window regulator motor assembly LH connector.

(b) Disconnect the V2 multiplex network door ECU (back door P/W) connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output (w/ Sliding Roof System)	A
DTC B2325 is output (w/o Sliding Roof System)	B
DTC B2325 is not output	C

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

A

1. CLEAR DTC

(a) Connect the V2 multiplex network door ECU (back door P/W) connector.

(b) Disconnect the S10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

(c) Clear the DTCs (See page ).

NEXT

1. CHECK FOR DTC

(a) Check for DTCs (See page ).

Result

Result	Proceed to
DTC B2325 is output	A
DTC B2325 is not output	B

A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)