K114 Continuously Variable Transmission

Replacement

~4min read
4special tools
0204060801004936N·mlb·ft
Tightening torque found on this page

REPLACEMENT

PRECAUTION / NOTICE / HINT

The procedures required (adjustment, calibration, initialization or registration) that must be performed after parts have been removed, installed or replaced during front differential oil seal removal/installation are shown below.

Procedure Required After Replacing / Removing / Installing Parts

Replacement part or procedure

Required Procedure

Effect/Inoperative function when procedure not performed

Link

CVT Fluid Replacement

ATF Thermal Degradation Estimate Reset

The value of the "ATF Thermal Degradation Estimate" Data List item is not estimated correctly.

PROCEDURE

1. REMOVE NO. 1 ENGINE UNDER COVER

Click here

2. REMOVE REAR LEFT ENGINE UNDER COVER

Click here

3. REMOVE REAR RIGHT ENGINE UNDER COVER

Click here

4. DRAIN CONTINUOUSLY VARIABLE TRANSMISSION FLUID

(a) Remove the filler plug and gasket from the continuously variable transmission assembly.

(b) Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the continuously variable transmission (CVT) oil pan sub-assembly and drain the fluid.

(c) Install a new gasket and the drain plug to the continuous variable transmission (CVT) oil pan sub-assembly.

Torque:

49 N·m {500 kgf·cm, 36 ft·lbf}

(d) Temporarily install the gasket and filler plug to the continuously variable transmission assembly.

HINT:

Reuse the old gasket. The filler plug must be removed again to adjust the fluid level.

5. REMOVE FRONT AXLE SHAFT ASSEMBLY

Click here

6. REMOVE AXLE SHAFT BEARING SUPPORT

Click here

7. REMOVE FRONT LEFT AXLE SHAFT OIL SEAL

(a) Using the SST, remove the front left axle shaft oil seal from the continuously variable transmission assembly.

SST: 09308-00010

NOTICE:

Take care not to damage the continuously variable transmission assembly.

8. REMOVE FRONT RIGHT AXLE SHAFT OIL SEAL

(a) Using the SST, remove the front right axle shaft oil seal from the continuously variable transmission assembly.

SST: 09308-00010

NOTICE:

Take care not to damage the continuously variable transmission assembly.

9. INSTALL FRONT LEFT AXLE SHAFT OIL SEAL

(a) Apply MP grease to the lip of a new front left axle shaft oil seal.

(b) Using the SST and a hammer, install the front left axle shaft oil seal to the continuously variable transmission assembly.

SST: 09316-10010

SST: 09950-70010

09951-07200

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

NOTICE:

  • Be sure to install the front axle shaft oil seal (left) in the correct direction.
  • Be sure to orient the front axle shaft oil seal (left) as specified, otherwise a malfunction such as fluid leakage may occur.
  • Do not damage the lip of the front axle shaft oil seal (left).

*a

-0.5 to 0.5 mm

10. INSTALL FRONT AXLE SHAFT OIL SEAL (RH)

(a) Apply MP grease to the lip of a new front axle shaft oil seal (RH).

(b) Using the SST and a hammer, install the front axle shaft oil seal (RH) to the continuously variable transaxle assembly.

SST: 09316-10010

SST: 09950-70010

09951-07200

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

NOTICE:

  • Be sure to install the front axle shaft oil seal (RH) in the correct direction.
  • Be sure to orient the front axle shaft oil seal (RH) as specified, otherwise a malfunction such as fluid leakage may occur.
  • Do not damage the lip of the front axle shaft oil seal (RH).

*a

-0.5 to 0.5 mm

11. INSTALL AXLE SHAFT BEARING BRACKET

Click here

12. INSTALL FRONT AXLE SHAFT ASSEMBLY

Click here

13. ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Click here

14. CHECK FOR FLUID LEAKAGE

15. INSTALL REAR LEFT ENGINE UNDER COVER

Click here

16. INSTALL REAR RH ENGINE UNDER COVER

Click here

17. INSTALL ENGINE UNDER COVER NO. 1

Click here