Audio / Video

Installation

~5min read
0102030405010.58N·mlb·ft
Tightening torque found on this page

INSTALLATION

PROCEDURE

1. INSTALL ANTENNA CABLE SUB-ASSEMBLY NO. 3

(a) without manual (SOS) switch

(1) Engage the clip and guide to temporarily install the antenna cable sub-assembly No. 3.

*A

for type A

*B

for type B

*C

for type C

*a

Guide

*b

Clip

(2) Install the bolt.

Torque:

for type A:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

for type B:

10 N·m {102 kgf·cm, 7 ft·lbf}

for type C:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) with manual (SOS) switch

(1) Engage the clip and guide to temporarily install the antenna cable sub-assembly No. 3.

*A

for type A

*B

for type B

*C

for type C

*a

Guide

*b

Clip

(2) Install the bolt.

(3) Connect the floor cable connector.

Torque:

for type A:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

for type B:

10 N·m {102 kgf·cm, 7 ft·lbf}

for type C:

10 N·m {102 kgf·cm, 7 ft·lbf}

(c) Engage the clips to install the antenna cable sub-assembly No. 3.

(d) Connect the connector.

2. INSTALL ANTENNA CABLE SUB-ASSEMBLY NO. 2

(a) Type A:

(1) Remove the old double-sided adhesive tape from the headlining.

*a

Marker

-

-

Double-sided adhesive tape

Front

(2) Prepare an appropriate amount of new double-sided adhesive tape.

HINT:

Be careful not to touch the adhesive surface of the product.

(3) Apply the double-sided adhesive tape to the headlining while aligning the tape with the markers on the headlining.

(4) Remove the protective sheet from the double-sided adhesive tape.

*a

Marking Tape (A)

*b

Marking Tape (B)

*c

Adhesive Tape (A)

*d

Adhesive Tape (B)

*e

Protrusion

*f

Headlining Edge

*g

Adjustment Area

-

-

Front

-

-

(5) Align marking tape (A) on the antenna cable sub-assembly No. 2 with the protrusion at the front of the headlining assembly, and wrap the adhesive tape around the antenna cable sub-assembly No. 2 and the headlining protrusion.

(6) Install the antenna cable sub-assembly No. 2 onto the double-sided adhesive tape on the headlining.

NOTICE:

  • Make sure there is no gap between the headlining sub-assembly and the antenna cable sub-assembly No. 2, and that the antenna cable sub-assembly No. 2 is not twisted.
  • Make sure the antenna cable sub-assembly No. 2 is properly installed. If any part of the antenna cable sub-assembly No. 2 is loose, an abnormal noise may occur.

(7) Align marking tape (B) on the antenna cable sub-assembly No. 2 with the headlining end on the headlining, and secure the antenna cable sub-assembly No. 2 using adhesive tape (A), as shown in the illustration.

NOTICE:

Make sure there is no gap between the headlining sub-assembly and the antenna cable sub-assembly No. 2, and that the antenna cable sub-assembly No. 2 is not twisted.

(8) Apply the 2 adhesive tapes (B) as shown in the illustration to secure the antenna cable sub-assembly No. 2.

HINT:

Secure the excess length of the antenna cable sub-assembly No. 2 in the adjustment area, as shown in the illustration.

(b) Type B:

(1) Align marking tape (A) on the antenna cable sub-assembly No. 2 with the protrusion at the front of the headlining assembly, and wrap the adhesive tape around the antenna cable sub-assembly No. 2 and the headlining protrusion.

*a

Marking Tape (A)

*b

Marking Tape (B)

*c

Adhesive Tape (A)

*d

Adhesive Tape (B)

*e

Protrusion

*f

Headlining Edge

*g

Adjustment Area

-

-

Front

-

-

(2) Install the antenna cable sub-assembly No. 2 onto the butyl tape on the headlining.

NOTICE:

  • Make sure there is no gap between the headlining sub-assembly and the antenna cable sub-assembly No. 2, and that the antenna cable sub-assembly No. 2 is not twisted.
  • Make sure the antenna cable sub-assembly No. 2 is properly installed. If any part of the antenna cable sub-assembly No. 2 is loose, an abnormal noise may occur.

(3) Align marking tape (B) on the antenna cable sub-assembly No. 2 with the headlining end on the headlining, and secure the antenna cable sub-assembly No. 2 using adhesive tape (A), as shown in the illustration.

NOTICE:

Make sure there is no gap between the headlining sub-assembly and the antenna cable sub-assembly No. 2, and that the antenna cable sub-assembly No. 2 is not twisted.

(4) Apply the 11 adhesive tapes (B) as shown in the illustration to secure the antenna cable sub-assembly No. 2.

HINT:

Secure the excess length of the antenna cable sub-assembly No. 2 in the adjustment area, as shown in the illustration.

3. INSTALL HEADLINING

Click here

4. INSTALL ANTENNA CABLE SUB-ASSEMBLY

(a) Engage the clips to install the antenna cable sub-assembly.

*A

with USB audio system

*B

with manual (SOS) switch

(b) with manual (SOS) switch:

(1) Connect the connector.

5. INSTALL NO. 3 HEATER DAMPER CONTROL CABLE ASSEMBLY

Click here

6. INSTALL INSTRUMENT PANEL SAFETY PAD

Click here