Rear Suspension

Installation

~4min read
1special tools
010203040502518N·mlb·ft
Tightening torque found on this page

INSTALLATION

PRECAUTION / NOTICE / HINT

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

(a) Secure the rear suspension support assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Install the rear suspension support assembly onto the rear shock absorber assembly.

(c) Apply a few drops of adhesive to the threads of a new nut between the rear support and the rear shock absorber.

Adhesive:

Adhesive 1324, Three Bond 1324 Toyota genuine or equivalent

(d) Using the SST and a 6 mm hex socket, hold the rear shock absorber rod and tighten a new nut between the rear support and the rear shock absorber.

SST: 09729-97202

Torque:

Specified torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

NOTICE:

Properly fit the 6 mm hex socket onto the rear shock absorber assembly rod to prevent damaging the rear shock absorber assembly when tightening the nut between the rear support and the rear shock absorber.

HINT:

  • Calculate the torque wrench reading when changing the torque wrench lever length.

    Click here

  • When using the SST (lever arm length 40 mm (1.57 in.)) + torque wrench (lever arm length 180 mm (7.09 in.)):

    20 N*m (204 kgf*cm, 15 lbf*ft)

*a

Torque wrench lever length

*b

Turn

*c

Hold

2. INSTALL REAR SHOCK ABSORBER CAP

(a) Install the rear shock absorber cap onto the rear shock absorber assembly.

3. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

(a) Temporarily install the rear shock absorber assembly onto the rear axle carrier sub-assembly using the nut.

NOTICE:

Hold the rear axle carrier pin while turning the nut.

4. STABILIZE SUSPENSION

(a) Using a jack and a wooden block, apply a load to the suspension so that the No. 2 suspension arm assembly is positioned as shown in the illustration.

Standard length A:

34.5 mm (1.36 in.)

  • Do not jack up the vehicle too high.
  • The vehicle may fall and cause a serious accident.

*a

Wooden Block

*b

Jack

Wooden Block Location

NOTICE:

  • When jacking up the No. 2 suspension arm assembly, be sure to do so slowly.
  • Be sure to perform this operation with the vehicle lowered as far as possible.

5. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY

(a) Temporarily install the rear upper control arm assembly onto the rear axle carrier sub-assembly using the bolt and nut.

NOTICE:

  • Insert the bolt with the threaded end facing the rear of the vehicle.
  • Do not turn the nut as it has a stopper. Tighten the bolt with the nut in place.

6. CONNECT REAR SHOCK ABSORBER ASSEMBLY

(a) Connect the rear shock absorber assembly to the vehicle using the 2 bolts.

Torque:

55 N·m {561 kgf·cm, 41 ft·lbf}

NOTICE:

Temporarily tighten bolt A, then fully tighten the 2 bolts in the order of B and A.

7. INSTALL REAR SHOCK ABSORBER ASSEMBLY

(a) Using a ball joint lock nut wrench, fully tighten the rear shock absorber assembly with the nut.

Torque:

Specified torque:

125 N·m {1 275 kgf·cm, 92 ft·lbf}

NOTICE:

Hold the rear axle carrier pin while turning the nut.

HINT:

  • Calculate the torque wrench reading when changing the torque wrench lever length.

    Click here

  • When using a ball joint lock nut wrench (lever arm length 150.25 mm (5.92 in.)) + torque wrench (lever arm length 400 mm (1.31 ft.)):

    91 N*m (928 kgf*cm, 67 lbf*ft)

*1

Rear Axle Carrier Pin

*a

Torque wrench lever length

*b

Ball Joint Lock Nut Wrench

*c

Turn

*d

Hold

8. INSTALL REAR UPPER CONTROL ARM ASSEMBLY

(a) Install the rear upper control arm assembly onto the rear axle carrier sub-assembly using the bolt.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

NOTICE:

Do not turn the nut as it has a stopper. Tighten the bolt with the nut in place.

9. INSTALL REAR STABILIZER LINK ASSEMBLY

Click here

10. INSTALL REAR LH HEIGHT CONTROL SENSOR SUB-ASSEMBLY (with Height Control Sensor)

Click here

11. INSTALL REAR WHEEL

Click here

12. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Click here

13. PERFORM INITIALIZATION (with Height Control Sensor)

Click here