Toyota Camry Quiz
Rear suspension

Rear suspension arm assy No.2 LH

In this manual: Rear suspension
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
30steps
~180min
4/5difficulty
030609012015010074N·mlb·ft
Tightening torque found on this page
Done 0 of 30
REPLACEMENT

HINT: COMPONENTS

  1. REMOVE REAR WHEEL
  2. REMOVE EXHAUST PIPE ASSY CENTER

  3. 1MZ−FE / 3MZ−FE engine:

  4. 2AZ−FE engine:

  5. REMOVE STABILIZER BAR REAR
  6. SEPARATE REAR SUSPENSION ARM ASSY No.1 LH
  7. SEPARATE REAR SUSPENSION ARM ASSY No.1 RH

HINT: Separate the RH side by the procedures with the LH side.

  1. SEPARATE REAR SUSPENSION ARM ASSY No.2 LH
  2. SEPARATE REAR SUSPENSION ARM ASSY No.2 RH

HINT: Separate the RH side by the procedures with the LH side.

  1. SEPARATE STRUT ROD ASSY REAR
  2. REMOVE REAR SUSPENSION MEMBER SUB−ASSY
  3. REMOVE REAR SUSPENSION ARM ASSY No.2 LH

a. Remove the bolt and disconnect the rear suspension arm No. 2 (inner side).

b. Remove the bolt, nut and the rear suspension arm No. 2

b. Remove the bolt, nut and the rear suspension arm No. 2 (outer side) from rear axle carrier.

HINT: Keep the nut fixed while loosening and removing the bolt.

11. INSTALL REAR SUSPENSION ARM ASSY No.2 LH
11. INSTALL REAR SUSPENSION ARM ASSY No.2 LH

a. Install the rear suspension arm No. 2 (inner side) with the bolt and temporarily tighten the bolt.

b. Set the suspension arm in the position in the illustration
b. Set the suspension arm in the position in the illustration and fully tighten the bolt.Torque: 100 N·m
  1. INSTALL REAR SUSPENSION MEMBER SUB−ASSY
  2. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY No.1 LH
  3. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY No.1 RH

HINT: Temporarily tighten the RH side by the procedures with the LH side.

  1. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY No.2 LH
  2. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY No.2 RH

HINT: Temporarily tighten the RH side by the procedures with the LH side.

  1. TEMPORARILY TIGHTEN STRUT ROD ASSY REAR
  2. INSTALL STABILIZER BAR REAR
  3. STABILIZE SUSPENSION
  4. FULLY TIGHTEN REAR SUSPENSION ARM ASSY No.1 LH
  5. FULLY TIGHTEN REAR SUSPENSION ARM ASSY No.1 RH

HINT: Fully tighten the RH side by the procedures with the LH side.

  1. FULLY TIGHTEN REAR SUSPENSION ARM ASSY No.2 LH
  2. FULLY TIGHTEN REAR SUSPENSION ARM ASSY No.2 RH

HINT: Fully tighten the RH side by the procedures with the LH side.

  1. FULLY TIGHTEN STRUT ROD ASSY REAR
  2. INSTALL EXHAUST PIPE ASSY CENTER

  3. 1MZ−FE / 3MZ−FE engine

  4. 2AZ−FE engine

  5. INSTALL REAR WHEEL Torque: 103 N·m
  6. INSPECT REAR WHEEL ALIGNMENT

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.