Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
TRANSMISSION OIL COOLER |
33493C |
- |
- |
|
2 |
NO. 2 WATER BY-PASS HOSE |
16264D |
- |
- |
|
3 |
INLET WATER HOSE |
16262 |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
![]() |
Toyota Genuine CVT Fluid FE |
- |
- |
- Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
4 |
ADD ENGINE COOLANT |
- |
- |
- |
|
5 |
ADJUST CONTINUOUSLY VARIABLE TRANSAXLE FLUID |
- |
- |
- |
|
6 |
INSPECT FOR COOLANT LEAK |
- |
- |
- |
|
7 |
INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK |
- |
- |
- |
|
8 |
REAR ENGINE UNDER COVER LH |
51444A |
- |
- |
- |
9 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
PROCEDURE
1. INSTALL TRANSMISSION OIL COOLER
![]() |
Toyota Genuine CVT fluid FE |
- |
- |
(1) Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle housing.
NOTICE:
Ensure that the O-rings are not twisted.
(2) Install the transmission oil cooler to the transaxle housing with the 3 bolts.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
2. CONNECT NO. 2 WATER BY-PASS HOSE
*a |
Paint Mark |
*b |
2 to 6 mm (0.0787 to 0.236 in.) |
(1) Connect the No. 2 water by-pass hose to the transmission oil cooler and slide the hose clip to secure it.
NOTICE:
- Make sure to slide the No. 2 water by-pass hose until it contacts the hose stopper of the transmission oil cooler.
- Make sure to align the paint mark of the No. 2 water by-pass hose with the paint mark of the transmission oil cooler.
- Make sure that the claws of the hose clip are within the location shown in the illustration.
3. CONNECT INLET WATER HOSE
*a |
Paint Mark |
*b |
2 to 6 mm (0.0787 to 0.236 in.) |
(1) Connect the inlet water hose to the transmission oil cooler and slide the hose clip to secure it.
NOTICE:
- Make sure to slide the inlet water hose until it contacts the hose stopper of the transmission oil cooler.
- Make sure to align the paint mark of the inlet water hose with the paint mark of the transmission oil cooler.
- Make sure that the claws of the hose clip are within the location shown in the illustration.
4. ADD ENGINE COOLANT
Click here ![]()
5. ADJUST CONTINUOUSLY VARIABLE TRANSAXLE FLUID
Click here ![]()
6. INSPECT FOR COOLANT LEAK
Click here ![]()
7. INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK
Click here ![]()
8. INSTALL REAR ENGINE UNDER COVER LH
9. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
.png)
.png)
.png)
.gif)
.png)
.png)
.png)