Toyota Corolla Quiz
Emission control

Engine rear oil seal

In this manual: Emission control
Introduction — 31Preparation — 32Service specifications — 19Diagnostics — 497Engine control system — 6Fuel — 13Emission control — 28Exhaust — 3Cooling — 13Lubrication — 7Ignition — 3Starting & charging — 13Front suspension — 12Rear suspension — 9Tire & wheel — 1Drive shaft / propeller shaft — 15Brake — 42Automatic transmission / trans — 47Clutch — 19Steering column — 9Power steering — 11Heater & air conditioner — 20Supplemental restraint system — 27Seat belt — 12Lighting — 18Wiper & washer — 9Audio & visual — 12Wiring — 1Communication system — 1Windshield/windowglass/mirror — 31Seat — 10Theft deterrent & door lock — 10Sliding roof/convertible — 8Engine hood/door — 12Exterior/interior trim — 20Vehicle control system — 1Cruise control — 5Maintenance — 8
14steps
~84min
3/5difficulty
Done 0 of 14
Replacement 1. Remove manual transaxle assy (m/t transaxle) 2. Remove automatic transaxle assy (a/t transaxle) 3. Remove clutch cover assy (m/t transaxle)
  1. remove the 6 bolts and clutch cover.
4. Remove clutch disc assy (m/t transaxle) 5. Remove flywheel sub–assy (m/t transaxle)
Toyota Corolla. Remove flywheel sub–assy
  1. Fix the crankshaft with sst, then remove the 8 bolts and flywheel.

    Sst 09960–10010 (09962–01000, 09963–01000)

6. Remove drive plate & ring gear sub–assy (a/t transaxle)
Toyota Corolla. Remove drive plate & ring gear sub–assy
  1. Fix the crankshaft with sst, then remove the 8 bolts and drive plate & ring gear.

    Sst 09960–10010 (09962–01000, 09963–01000)

7. Remove engine rear oil seal
Toyota Corolla. Remove engine rear oil seal
  1. Using a knife, cut off the oil seal lip.
  2. using a screwdriver with taping its tip, pry out the oil seal.
Notice

: after the removal, check if the crankshaft is not damaged.

If there is, mend it with a sandpaper (#400).

 8. Install engine rear oil seal
Toyota Corolla. Install engine rear oil seal
  1. Apply mp grease to a new oil seal lip.
Notice

: keep the lip off foreign materials.
  1. using sst, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.

    Sst 09223–15020, 09950–70010 (09951–07100)

Notice

: wipe off extra grease on the crankshaft.

 9. Install flywheel sub–assy (m/t transaxle)
Toyota Corolla. Install flywheel sub–assy
  1. Fix the crankshaft with sst.

    Sst 09960–10010 (09962–01000, 09963–01000)

    Toyota Corolla. Install flywheel sub–assy
  2. Clean the bolt and bolt hole.
  3. apply adhesive to the bolts.

    Adhesive: part no. 09330–00070, Three bond or equivalent.

  4. install and uniformly tighten the 8 bolts, in several passes, in the sequence shown.

    Torque: 49 nvm (500 Kgf·cm, 36 ft·lbf)

    Toyota Corolla. Install flywheel sub–assy
  5. Mark the bolts with paint.
  6. retighten the bolts by an additional 90 .
  7. check that the point marked bolts are moved at 90 angle.
10. Install clutch disc assy (m/t transaxle) sst 09301–00210 11. Install clutch cover assy (m/t transaxle) 12. Install drive plate & ring gear sub–assy (a/t transaxle)
Toyota Corolla. Install drive plate & ring gear sub–assy
  1. Fix the crankshaft with sst.

    Sst 09960–10010 (09962–01000, 09963–01000)

    Toyota Corolla. Install drive plate & ring gear sub–assy
  2. Clean the bolt and bolt hole.
  3. apply adhesive to the bolts.

    Adhesive: part no. 09330–00070, Three bond or equivalent.

  4. install and uniformly tighten the 8 bolts, in several passes, in the sequence shown.
  5. fix the crankshaft with sst.

    Torque: 88 nvm (897 Kgf·cm, 65 ft·lbf)

13. Install manual transaxle assy (m/t transaxle) 14. Install automatic transaxle assy (a/t transaxle)

Test yourself

A quick Toyota Corolla quiz: every answer comes with an explanation and a link to the manual page.