Toyota Sienna Quiz
Axle

Installation

In this manual: Axle
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
~2min read

1. INSTALL FRONT AXLE ASSEMBLY LH

INSTALL FRONT AXLE ASSEMBLY LH

(a) Install the 2 bolts, nuts and front axle assembly LH with the 2 bolts and nuts to the shock absorber assembly front LH.

Torque: 230 N*m (2,350 kgf*cm, 170 ft.*lbf)

NOTICE:

  • Only when reusing the bolts and nuts, apply the small amount of engine oil to the screw part of the nuts.
  • Do not excessively push out the front axle assembly LH.
  • Be careful not to damage the outboard joint boot.
  • Be careful not to damage the speed sensor rotor.

2. INSTALL FRONT SUSPENSION ARM SUBASSEMBLY LOWER NO.1 LH (See page DS-18)

3. INSTALL TIE ROD END SUB-ASSEMBLY LH (See page DS-18)

4. INSTALL FRONT DISC

5. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

(a) Install the front disc brake caliper assembly LH with the 2 bolts to the steering knuckle LH.

Torque: 104 N*m (1,060 kgf*cm, 77 ft.*lbf)

6. INSTALL FRONT AXLE HUB LH NUT

(a) Using a socket wrench (30mm), install a new axle hub LH nut.

Torque: 294 N*m (3,000 kgf*cm, 217 ft.*lbf)

7. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY LH

(a) Remove the 2 bolts and separate the front disc brake caliper assembly LH from the steering knuckle LH.

NOTICE: Use a string or other device to keep the brake caliper from hanging down.

8. REMOVE FRONT DISC

9. INSPECT BEARING BACKLASH (See page AH-5)

10. INSPECT AXLE HUB DEVIATION (See page AH-5)

11. INSTALL FRONT DISC

12. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

(a) Install the front disc brake caliper assembly LH with the 2 bolts to the steering knuckle LH.

Torque: 104 N*m (1,060 kgf*cm, 77 ft.*lbf)

13. INSTALL SPEED SENSOR FRONT LH (See page DS- 18)

14. INSTALL FRONT AXLE HUB LH NUT

INSTALL FRONT AXLE HUB LH NUT

(a) Using a socket wrench (30 mm), install a new axle hub LH nut.

Torque: 294 N*m (3,000 kgf*cm, 217 ft.*lbf) (b) Using a chisel and hammer, stake the axle hub LH nut.

15. INSTALL FRONT WHEEL Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)

16. INSPECT FRONT WHEEL ALIGNMENT

(a) Inspect front wheel alignment (See page SP-4).

17. CHECK ABS SPEED SENSOR SIGNAL

(a) ABS WITH EBD SYSTEM (See page BC-3).

(b) ABS WITH EBD & BA & TRAC & VSC SYSTEM (See page BC-72).

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.