Toyota Sienna Quiz
Supplemental restraint system

Open in Occupant Classification ECU Battery Positive Line

In this manual: Supplemental restraint system
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
15steps
~90min
4/5difficulty
Done 0 of 15

DTC B1794 Open in Occupant Classification ECU Battery Positive Line

DESCRIPTION

This circuit consists of the occupant classification ECU and the power source circuit (battery, fuse, wire harness).

DTC B1794 is recorded when a malfunction is detected in the occupant classification ECU or the power source circuit.

HINT: When DTC B1794 is output after switching the ignition switch LOCK-ON-LOCK 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system, the DTC is output again when a malfunction is detected even once after being cleared, unless the normal system code is

DTC No.

DTC Detecting Condition

Trouble Area

B1794
  • The ignition switch is turned from LOCK to ON, hold for 10 seconds or more, and back to LOCK again 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system.
  • Occupant classification ECU malfunction
  • Battery
  • ECU-B Fuse
  • Floor wire No. 2
  • Front seat wire RH
  • Occupant classification ECU

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

1 CHECK BATTERY

  1. Measure the voltage of the battery.
Standard: 11 to 14 V

2 CHECK FUSE

  1. Check the ECU-B fuse.
Standard: Below 1 Ω

3 CHECK WIRE HARNESS

CHECK WIRE HARNESS
  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the occupant classification ECU.
  4. Connect the negative (-) terminal cable to the battery.
  5. Turn the ignition switch to the ON position.
  6. Measure the voltage and resistance according to the value(s) in the table below.

Standard voltage

Standard voltage
  1. Turn the ignition switch to the LOCK position.
  2. Measure the resistance and resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

4 CHECK DTC

  1. Turn the ignition switch to the ON position.

(b) Clear the DTCs stored in memory (35).

HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  • Turn the ignition switch to the LOCK position.
  • Turn the ignition switch to the ON position, and wait for at least 10 seconds.
  • Using the intelligent tester, check the DTCs of the occupant classification ECU (35).

    • OK: DTC B1794 is not output. HINT: Codes other than code B1794 may be output at this time, but they are not related to this check.

    USE SIMULATION METHOD TO CHECK

    5 REPLACE OCCUPANT CLASSIFICATION ECU

    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Replace the occupant classification ECU

    6 PERFORM ZERO POINT CALIBRATION

    1. Connect the negative (-) terminal cable to the battery.
    2. Connect the intelligent tester to the DLC3.
    3. Turn the ignition switch to the ON position.
    4. Using the intelligent tester, perform the "Zero point calibration" (28).

    OK: The "COMPLETED" is displayed.

    7 PERFORM SENSITIVITY CHECK

    1. Using the intelligent tester, perform the "Sensitivity check"

    Standard value: 27 to 33 kg (59.52 to 72.75 lb)

    END

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.