Toyota Tacoma Quiz
Park Assist / Monitoring

How To Proceed With Troubleshooting

In this manual: Park Assist / Monitoring
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~1min read
CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the intuitive parking assist system.
  • *: Use the Techstream.
PROCEDURE

  1. VEHICLE BROUGHT TO WORKSHOP

NEXT

  1. CUSTOMER PROBLEM ANALYSIS

NEXT

  1. INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

NEXT

  1. CHECK CAN COMMUNICATION SYSTEM*

(a) Use the Techstream to check if the CAN communication system is functioning normally.

Click here

Result

Proceed to

CAN communication system DTCs are not output

A

CAN communication system DTCs are output

B
B

GO TO CAN COMMUNICATION SYSTEM

A

  1. PROBLEM SYMPTOM CONFIRMATION

NEXT

  1. CHECK DTC*

(a) Check for DTCs.

Click here

Result

Proceed to

DTCs are output

A

DTCs are not output (Problem symptom does not occur)

B

DTCs are not output (Problem symptom occurs)

C
B

GO TO STEP 8
C

GO TO STEP 9
A

  1. DIAGNOSTIC TROUBLE CODE CHART

(a) Refer to Diagnostic Trouble Code Chart.

Click here

NEXT

GO TO STEP 11

  1. SYMPTOM SIMULATION

(a) Refer to Symptom Simulation.

Click here

NEXT

  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B
B

GO TO STEP 11
A

  1. OVERALL ANALYSIS AND TROUBLESHOOTING

(a) Operation Check

Click here (b) Terminals of ECU

(b) Terminals of ECU

Click here (c) Data List / Active Test

(c) Data List / Active Test

Click here

NEXT

  1. CIRCUIT INSPECTION*

NEXT

  1. IDENTIFICATION OF PROBLEM

NEXT

  1. REPAIR OR REPLACE

NEXT

  1. CONFIRMATION TEST*

NEXT

END

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.