Toyota Tacoma Quiz
Ac60e Automatic Transmission / Transaxle

Inspection

In this manual: Ac60e Automatic Transmission / Transaxle
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
INSPECTION PROCEDURE

1. INSPECT SHIFT SOLENOID VALVE SL1

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*a

Component without harness connected

(Shift Solenoid Valve SL1)

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20 °C

5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve SL1.

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition

Specified Condition
  • Battery positive (+) with a 21 W bulb → Terminal 1
  • Battery negative (-) → Terminal 2

Valve moves and makes an operating noise

If the operation cannot be done as specified, replace the shift solenoid valve SLT.

2. INSPECT SHIFT SOLENOID VALVE SL2

HINT:

Refer to Inspect Shift Solenoid Valve SL1.

3. INSPECT SHIFT SOLENOID VALVE SL3

HINT:

Refer to Inspect Shift Solenoid Valve SL1.

4. INSPECT SHIFT SOLENOID VALVE SL4

HINT:

Refer to Inspect Shift Solenoid Valve SL1.

5. INSPECT SHIFT SOLENOID VALVE SLU

HINT:

Refer to Inspect Shift Solenoid Valve SL1.

6. INSPECT SHIFT SOLENOID VALVE SLT

HINT:

Refer to Inspect Shift Solenoid Valve SL1.

7. INSPECT SHIFT SOLENOID VALVE SL

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*a

Component without harness connected

(Shift Solenoid Valve SL)

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve SL connector terminal - Shift solenoid valve SL body

20 °C

11 to 15 Ω

If the value is not as specified, replace the shift solenoid valve SL.

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition

Specified Condition
  • Battery positive (+) → Shift solenoid valve SL connector
  • Battery negative (-) → Shift solenoid valve SL body

Valve moves and makes an operating noise

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.