Toyota Tacoma Quiz
Other System

Wireless Charger Main Switch

In this manual: Other System
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
Components COMPONENTS ILLUSTRATION Removal Removal REMOVAL PROCEDURE

1. REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

(See page 2. REMOVE MOBILE WIRELESS CHARGER SWITCH )

2. REMOVE MOBILE WIRELESS CHARGER SWITCH

(a) Disengage the 2 claws to remove the mobile wireless charger switch.
Inspection INSPECTION PROCEDURE

1. INSPECT MOBILE WIRELESS CHARGER SWITCH

(a) Check the mobile wireless charger switch.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

11 (ACC) - 8 (SW)

Mobile wireless charger switch is on (not protruding)

Below 1 Ω

Mobile wireless charger switch is off (protruding)

10 kΩ or higher
Text in Illustration

*a

Component without harness connected

(Mobile Wireless Charger Switch)

If the result is not as specified, replace the mobile wireless charger switch.

(b) Check that the switch indicator light illuminates.

(1) Apply battery voltage to the mobile wireless charger switch connector and check the operation of the switch indicator light.

OK:

Connection

Condition

Specified Condition

Battery positive (+) → Terminal 11 (ACC)

Battery negative (-) → Terminal 12 (GND)

Mobile wireless charger switch is on (not protruding)

Switch indicator light illuminates

Mobile wireless charger switch is off (protruding)

Switch indicator light does not illuminates
Text in Illustration

*a

Component without harness connected

(Mobile Wireless Charger Switch)

If the result is not as specified, replace the mobile wireless charger switch.

(c) Check that the switch illuminates.

(1) Apply battery voltage to the mobile wireless charger switch and check that the switch illuminates.

OK:

Connection

Specified Condition

Battery positive (+) → Terminal 10 (ILL+)

Battery negative (-) → Terminal 9 (ILL-)

Illuminates
Text in Illustration

*a

Component without harness connected

(Mobile Wireless Charger Switch)

If the result is not as specified, replace the mobile wireless charger switch.
Installation INSTALLATION PROCEDURE

1. INSTALL MOBILE WIRELESS CHARGER SWITCH

(a) Engage the 2 claws to install the mobile wireless charger switch.

2. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL

(See page Wireless Charging System )

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.