DESCRIPTION
- If the manual UP/DOWN function does not operate, there may be a malfunction in the master switch, the driver side motor, or the harness or connector.
WIRING DIAGRAM
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
CHECK LIN COMMUNICATION SYSTEM
(a) Check for LIN communication system DTCs related to the power window control system (See page ).
OK:
LIN communication system DTCs are not output.
| NG |
 |
GO TO LIN COMMUNICATION SYSTEM |
| OK |
 |
|
CHECK FOR DTC (B2312)
(a) Check if DTC B2312 is output (See page ).
OK:
DTC B2312 is not output.
| NG |
 |
GO TO DTC (B2312) |
| OK |
 |
|
READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR)
(a) Use the Data List to check if the driver side motor is functioning properly. D-Door Motor
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
D Door P/W Up SW |
Driver side power window MANUAL UP switch signal / ON or OFF |
ON: Driver side switch operated
OFF: Driver side switch not operated |
- |
D Door P/W Down SW |
Driver side power window MANUAL DOWN switch signal / ON or OFF |
ON: Driver side switch operated
OFF: Driver side switch not operated |
- |
OK:
The Techstream display changes normally when master switch is operated.
| OK |
 |
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
| NG |
 |
|
CHECK HARNESS AND CONNECTOR (MASTER SWITCH - BATTERY AND BODY GROUND)
(a) Disconnect the master switch connector. |
 |
*a |
Front view of wire harness connector
(to Master Switch) |
|
|
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
N2-3 (B) - Body ground |
Always |
11 to 14 V |
N2-13 (B) - Body ground |
Ignition switch ON |
11 to 14 V |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
N2-1 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (DRIVER SIDE MOTOR - BATTERY AND BODY GROUND)
(a) Disconnect the motor connector. |
 |
*a |
Front view of wire harness connector
(to Driver Side Motor) |
|
|
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
N12-2 (B) - Body ground |
Always |
11 to 14 V |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
N12-1 (GND) - Body ground |
Always |
Below 1 Ω |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
(a) Disconnect the N2 master switch connector.
(b) Disconnect the N12 motor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
N2-4 (UP) - N12-10 (UP) |
Always |
Below 1 Ω |
N2-5 (DOWN) - N12-7 (DOWN) |
Always |
Below 1 Ω |
N2-4 (UP) - Body ground |
Always |
10 kΩ or higher |
N2-5 (DOWN) - Body ground |
Always |
10 kΩ or higher |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
(a) Remove the driver side motor (See page ). |
 |
*1 |
Motor Gear |
*a |
Component without harness connected
(Driver Side Motor) |
*b |
Counterclockwise |
*c |
Clockwise |
|
|
(b) Apply positive (+) battery voltage to connector terminal 2 (B).
NOTICE:
- Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.
- Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.
(c) Apply negative (-) battery voltage to connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).
(d) Check that the motor gear rotates smoothly as follows.
OK:
Measurement Condition | Specified Condition |
Battery positive (+) → 2 (B)
Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 10 (UP) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 10 (UP) |
Motor gear rotates clockwise |
Battery positive (+) → 2 (B)
Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 7 (DOWN) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 7 (DOWN) |
Motor gear rotates counterclockwise |
| OK |
 |
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
| NG |
 |
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
|