Vehicle Interior
Inspection
INSPECTION
PROCEDURE
1. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
(a) Inspect the light control switch.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Switch Condition | Specified Condition |
20 (H) - 12 (EL) |
Light control switch off or DRL OFF |
10 kΩ or higher |
18 (T) - 12 (EL) |
19 (A) - 12 (EL) |
18 (T) - 12 (EL) |
Light control switch tail |
Below 1 Ω |
18 (T) - 12 (EL) |
Light control switch head |
Below 1 Ω |
20 (H) - 12 (EL) |
19 (A) - 12 (EL) |
Light control switch auto |
Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly. Text in Illustration
*a |
Component without harness connected
(Headlight Dimmer Switch Assembly) |
(b) Inspect the headlight dimmer switch.
(1) Measure the resistance according to the value(s) in the table below.
HINT:
Perform the flash, high beam and low beam inspections with the light control switch on head.
Standard Resistance:
Tester Connection | Switch Condition | Specified Condition |
11 (HU) - 12 (EL) |
Headlight dimmer switch flash |
Below 1 Ω |
17 (HF) - 12 (EL) |
11 (HU) - 12 (EL) |
Headlight dimmer switch hi beam |
Below 1 Ω |
16 (HL) - 12 (EL) |
Headlight dimmer switch low beam |
Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly. Text in Illustration
*a |
Component without harness connected
(Headlight Dimmer Switch Assembly) |
|
 |
(c) Inspect the turn signal switch.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Switch Condition | Specified Condition |
13 (TR) - 12 (EL)
15 (TL) - 12 (EL)
14 (CR) - 12 (EL) |
Turn signal switch neutral |
10 kΩ or higher |
13 (TR) - 12 (EL) |
Turn signal switch right turn |
Below 1 Ω |
13 (TR) - 12 (EL)
11 (TL) - 14 (CR)
14 (CR) - 12 (EL) |
Turn signal switch right lane change |
Below 1 Ω |
15 (TL) - 12 (E) |
Turn signal switch left turn |
Below 1 Ω |
15 (TL) - 12 (EL)
15 (TL) - 14 (CR)
14 (CR) - 12 (EL) |
Turn signal switch left lane change |
Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly. Text in Illustration
*a |
Component without harness connected
(Headlight Dimmer Switch Assembly) |
|
 |
(d) Inspect the front fog light switch.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Switch Condition | Specified Condition |
3 (LFG) - 4 (BFG) |
Front fog light switch off |
10 kΩ or higher |
3 (LFG) - 4 (BFG) |
Front fog light switch on |
Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly. Text in Illustration
*a |
Component without harness connected
(Headlight Dimmer Switch Assembly) |
|
 |
|
Was this page helpful?