Toyota Venza Quiz
2gr-fe Battery / Charging

Disassembly

In this manual: 2gr-fe Battery / Charging
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~1min read
9special tools
DISASSEMBLY PROCEDURE

1. REMOVE GENERATOR REAR END COVER

(a) Remove the 3 nuts and generator rear end cover.

2. REMOVE TERMINAL INSULATOR

(a) Remove the terminal insulator from the generator coil.

3. REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

(a) Remove the 2 screws and brush holder from the generator coil.

4. REMOVE GENERATOR COIL ASSEMBLY

(a) Remove the 4 bolts.

(b) Using SST, remove the generator coil assembly.

Text in Illustration

*1

Turn

*2

Hold

SST: 09950-40011

09951-04020

09952-04010

09953-04020

09954-04010

09955-04071

09957-04010

09958-04011

(c) Remove the generator washer.

5. REMOVE GENERATOR CLUTCH PULLEY

(a) Using a screwdriver, remove the generator pulley cap.

NOTICE:

Do not reuse the generator pulley cap.

(b) Mount the generator drive end frame in a vise tightly.

(c) Confirm SST (A) and (B) shown in the illustration.

Text in Illustration

*1

SST (A)

*2

SST (B)

SST: 09820-63021

(d) Place the rotor shaft end into SST (A).

Text in Illustration

*1

Rotor Shaft

*2

SST (A)

(e) Fit SST (B) to the clutch pulley.

Text in Illustration

*1

Clutch Pulley

*2

SST (B)

*3

SST (A)

(f) Loosen the pulley by turning SST (B) in the direction shown in the illustration.

Text in Illustration

*1

SST (B)

*2

SST (A)

NOTICE:

  • Check that the drive end frame is secured in the vise tightly.
  • Hold SST (A) tightly during the operation.

(g) Remove SST from the generator assembly.

(h) Remove the clutch pulley from the rotor shaft.

6. REMOVE GENERATOR ROTOR ASSEMBLY

(a) Remove the generator rotor assembly.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.