Toyota Venza Quiz
Axle And Differential

Installation

In this manual: Axle And Differential
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
090180270360450290214N·mlb·ft
Tightening torque found on this page
INSTALLATION CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.
PROCEDURE

1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

(a) Temporarily install the rear axle carrier sub-assembly with the 2 bolts and 2 nuts.

NOTICE:

  • Be careful not to damage the outboard joint boot.
  • Be careful not to damage the speed sensor rotor.
  • Keep the speed sensor rotor free of foreign matter.

(b) Install the rear axle carrier sub-assembly with the 2 bolts and 2 nuts.

Torque:

290 N·m {2957 kgf·cm, 214 ft·lbf}

NOTICE:

  • Be careful not to damage the outboard joint boot.
  • Be careful not to damage the speed sensor rotor.
  • Keep the speed sensor rotor free of foreign matter.
  • Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
  • When installing the nuts, keep the bolts from rotating.

HINT:

Insert the bolts from the rear side.

(c) Fully tighten the rear No. 2 suspension arm assembly and the rear No. 1 suspension arm assembly with the 2 bolts and 2 nuts.

Torque:

112 N·m {1141 kgf·cm, 82 ft·lbf}

NOTICE:

Since stopper nuts are used, tighten the bolts.

2. INSTALL REAR STRUT ROD ASSEMBLY


3. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


4. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY


5. INSTALL REAR SPEED SENSOR


6. INSTALL REAR DISC


7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


8. INSTALL REAR AXLE SHAFT NUT


9. INSTALL REAR WHEEL

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

10. STABILIZE SUSPENSION


11. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

(a) Inspect and adjust the front wheel alignment (See page ).


12. CHECK FOR SPEED SENSOR SIGNAL

(a) Check for the speed sensor signal (See page ).

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.