Preservation

Preserving Wax

Definition:

• Preserving Wax -AKR 321 M15 4-
• Preserving Wax -AKR 321 M16 10-

Product Description

Preserving Wax -AKR 321 M15 4- and Preserving Wax -AKR 321 M16 10- are spray-on wax-based rust-protection agents.

After drying, a strongly adhesive, viscous plastic-like and waterproof film which is more or less colorless.

The flow point of the dry substance is over +100 ºC (212 ºF), meaning that running or dripping is unlikely even in the engine compartment.

The dry film adheres well to bare and painted surfaces.

Application Instructions

Application

• Is used for the preservation of seams, surfaces and cavities in vehicles.
• Its bright color makes it especially suitable for protecting the seams of the hood and in the luggage compartment.
• The material is also preferred for treating the cleaned engine compartment.

Processing

Note

• Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.
• Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions.

• Thoroughly clean and dry the parts that are to be treated with preserving wax. Remove any rust.
• Shake the can well before use. Spray on the preserving wax and let it dry. It should not be sprayed on visible exterior parts as the dry film has a matt appearance.

Caution

When preserving the engine compartment of vehicles and motors of other equipment, the engines or motors should only be switched on after the protective wax film has been allowed to ventilate thoroughly. There is a danger of explosions due to evaporated solvents!

Technical Data

Color	Transparent in thin coats
Odor	Mild odor
Viscosity (DIN 53211, 4 mm)	12 to 14 seconds
Dropping point	approximately 100 ºC (212 ºF)
Cleaning	With turpentine, cold cleaner or kerosene
Processing temperature	+15 ºC to +30 ºC (59º to 86 ºF)

Cavity Sealant

Definition:

• Cavity Sealant -D 330 KD1 A2-
• Cavity Sealant -D 330 KD2 A1-

Product Description

Cavity Sealant -D 330 KD1 A2- and Cavity Sealant -D 330 KD2 A1- are anti-corrosion agents containing solvents for sealing cavities with a high solid matter content.

As a thixotrope it has a well atomized solution and is therefore ideal for protecting areas that are difficult to access and narrow gaps between sheets of metal.

The cavity sealant infiltrates and pushes out moisture, it contains a high proportion of anti-rusting agent.

The cavity sealant atomizes very finely when sprayed, spreads very well, and penetrates all of the gaps to be protected (for example, welded joints), however, does not run too strongly out of the lower side of the weld.

The material can also be used at low temperatures above 10 ºC (50 ºF), and its flow characteristics are improved when the product and the bodywork are at room temperatures.

After drying, the material forms a plastic-like, waterproof film in a transparent beige color.

Application Instructions

Application

• Is mostly used in garages for spraying the interior of cavities to supplement the cavity sealing for new vehicles and to treat cavity sealing after two to three years and in accident repair.

Note

• Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.
• Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions

Cavity Sealant -D 330 KD1 A2- processing

• The Cavity Sealant -D 330 KD1 A2- can be easily applied with the pressure feed spray gun and the appropriate probes.
• The application pressure for the pressure feed spray gun is 5 to 6 bar. The material pressure reducer should be set to 5 bar.
• If it is stored for a long time or if the temperature falls below +10 ºC (+50 ºF) the material becomes more thixotropic. This is broken however during spraying at the application temperature. The product shows its usual characteristics after spraying.

Note

Depending on the type of the cavity to be treated, the drying phase can last several days. Ensure that the vehicle is well ventilated during the drying process.

Cavity Sealant -D 330 KD2 A1- processing

• Trim panels and trim should be removed. Any rust should be removed as far as possible.
• For surfaces that are difficult to reach (such as semi-hollow spaces in doors) should be sprayed with the spraying hose from the lid instead of the spraying head.
• The material should be at room temperature during application.
• If it is stored for a long time or if the temperature falls below +10 ºC (+50 ºF) the material becomes more thixotropic. Shake the can thoroughly before use until the rattling of the balls becomes audible.
• The body parts should be cleaned of dust and grease and then sprayed evenly. The can should be held in a vertical position when spraying.
• When working with the "spraying hose", it can be slowly guided in circles in all directions.
• The spraying head with the round spraying nozzle enables the operator to apply a fine even coat on surfaces such as the underbody, giving these a perfect appearance.

Note

The Cavity Sealant -D 330 KD2 A1- is a product with a flammable propellant gas. Make sure that the cavities are well ventilated before closing again (for example, door trim panels) and that the vehicle is well ventilated during drying. Depending on the type of the cavity to be treated, the drying phase can last several days.

Caution

Do not spray functional parts such as the brake and exhaust systems.

Rubber and plastic parts should also not be sprayed.

Cleaning

• Dripping cavity sealant can be easily wiped away.
• The Plastic Cleaner -D 195 850 A1- is suitable for cleaning dried material.
• Larger surfaces can be cleaned with a steam cleaner. Splashes on painted surfaces should be removed immediately.

Cavity Sealant -D 330 KD1 A2- technical data

Color	Beige transparent
Odor	Typical smell of its own
Solid matter content	Approximately 60% (active ingredients)
Consistency	Thixotropic
Stability	at least 100 μm
Top coat compatibility	No permanent change to the paint
Removability after 24 hours	Dry material can be easily removed
Characteristics in drying oven (1.5 hours at 90 ºC (194 ºF) )	Does not drip
Frost resistance	Does not crack
Corrosion resistance	Does not corrode
Processing temperature	+10 ºC to +25 ºC (50º to 77 ºF)
Application temperature	-40 ºC to +90 ºC (-40 º to 194 ºF)

Cavity Sealant -D 330 KD2 A1- technical data

Color	Beige transparent (almost transparent)
Odor	Typical smell of its own
Solid matter content	Approximately 60% (active ingredients)
Dropping point of the solid matter	approximately 150 ºC (302 ºF)
Consistency	Thixotropic
Stability	at least 100 μm
Penetration	greater than 16 cm
Top coat compatibility	No permanent change to the paint
Removability after 24 hours	Dry material can be easily removed
Characteristics in drying oven (1.5 hours at 90 ºC)	Does not drip
Frost resistance	Does not crack
Corrosion resistance	Does not corrode
Processing temperature	+10 ºC to +25 ºC (50º to 77 ºF)
Application temperature	-40 ºC to +90 ºC (-40 º to 194 ºF) (+120 ºC (248 ºF) short-term, up to one hour)

Preserving Wax (Spray Can)

Definition:

• Preserving Wax -D 308 SP5 A1-

Product Description

The Preserving Wax -D 308 SP5 A1- provides optimal corrosion protection for areas in the body that are most at risk for corrosion, such as steel trim (folded edges, gaps, flanges), edges and surfaces.

This long-term corrosion protection is established through sufficient penetration as well as exceptional adhesion to the metallic surface.

The top coat compatibility and removability as well as the compatibility with the rubber and plastic attachments is created.

Application Instructions

Application

• The recommended dry layer thickness is approximately 30 μm.

Technical Data

Propane-butane content	45 to 49 %
Active ingredient content	22 to 26 %
Solvent content	27 to 31 %
Viscosity (DIN 53211, 4 mm)	16 to 22 seconds
Dropping point (of solid matter)	greater than 150 ºC (302 ºF)
Cleaning	with mineral spirits
Processing temperature	+18 ºC through +25 ºC (+64.4º through +77 ºF)
Flashpoint PM (DIN EN 22719)	+27 ºC through +33 ºC (80.6º through 91.4 ºF)
Color	light beige
Application temperature	+10 ºC to +30 ºC (50 ºF to 86 ºF)
Frost resistance	through -30 ºC (-22 ºF)