5-speed manual transmission 0CF

Clutch

4steps
~24min
2/5difficulty
010203040501310N·mlb·ft
Tightening torque found on this page
Done 0 of 4

Assembly overview - clutch

VW UP. 5 Gang-Schaltgetriebe 0CF

  1. Flywheel
    • Remove and install
    • Make sure the centering pins are firmly seated
    • Keep the contact surface for the friction lining free of grooves, oil and grease
  2. Clutch disc
    • Assignment → Electronic Parts Catalog (ETKA)
    • center
  3. Pressure plate
    • Remove and install
    • Check the ends of the diaphragm spring
    • Check spring connections and rivet connections
  4. Bolt
    • Assignment → Electronic Parts Catalog (ETKA)
    • loosen or tighten in small steps, in a crosswise sequence
    • M 6: 13 N·m
    • M 7: 20 N·m

Remove and install clutch

VW UP. 5 Gang-Schaltgetriebe 0CF

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Counterholder -3067-
  • Centering mandrel -3190 A-
  • Torque Wrench -V.A.G 1331-
  • Grease for clutch disc splines -G 000 100-

Removing

  • Transmission removed

- Insert counterhold -3067- to loosen the bolts.

To prevent the pressure plate from deforming during removal (which causes judder when pulling away), unscrew the clutch pressure plate as follows:

- Loosen all bolts in small steps in a crisscross pattern.

- Remove the pressure plate and the clutch disc.

Installing


Note

  • Assign clutch pressure plate and clutch disc via engine code letters → Electronic Parts Catalog.
  • Clean the splines of the input shaft and, on a used clutch disc, the splines of the hub. Remove corrosion and apply only a paper-thin layer of grease for clutch disc spline -G 000 100- to the splines. Then move the clutch disc back and forth on the input shaft until the hub moves freely on the shaft. Be sure to remove excess grease.
  • Clutch pressure plates are corrosion-protected and greased. Except for the friction surface for the clutch disc, the clutch pressure plate must not be cleaned. Otherwise the service life of the clutch will be significantly reduced.
  • The friction surfaces of the clutch pressure plate and flywheel must be thoroughly cleaned (degreased).
  • To reduce odor from a burnt clutch, thoroughly clean the transmission in the clutch area and the engine on the transmission side.
  • The linings of the clutch disc must rest fully against the flywheel and the friction surface of the clutch pressure plate. Only then insert the fastening bolts.
  • Tighten the fastening bolts in small steps in a crisscross pattern to avoid damaging the centering holes of the pressure plate and the centering pins of the flywheel.
  • Check whether locating sleeves for engine/transmission centering are present in the cylinder block; install if necessary.
  • If locating sleeves are missing, shifting difficulties, clutch problems and possibly transmission noise (idler gear rattle) may occur.
VW UP. 5 Gang-Schaltgetriebe 0CF

  • Installed position of the clutch disc: the marking "transmission side" or the spring cage faces the pressure plate.
VW UP. 5 Gang-Schaltgetriebe 0CF

Check the ends of the diaphragm spring

  • Wear up to half the thickness of the diaphragm spring -arrows- is permissible.
VW UP. 5 Gang-Schaltgetriebe 0CF

Check spring connection and rivet connections

- Check the spring connection between pressure plate and cover for cracks, and the rivet connections for tight fit.

- A pressure plate with damaged springs or loose rivet connections -arrows- must be replaced.

VW UP. 5 Gang-Schaltgetriebe 0CF

Check tension springs and rivet connection

I - Tension springs OK

  • Slight kinks on the outer area -arrows A- are production condition.

II - Tension springs damaged

  • Clutch pressure plates with kinked or broken tension springs -arrow B- must be replaced.

- Check spring connections -arrows A- for damage and rivet connections -arrows B- for tight fit.

  • A clutch pressure plate with severely kinked or broken spring connections, or loose rivet connections, must be replaced.
VW UP. 5 Gang-Schaltgetriebe 0CF

- Check rivet connections -arrows B- on all tension springs -arrows A- for tight fit.

- Tighten all bolts one after another in a clockwise sequence to final torque.

  • Replace clutch pressure plates with loose rivet connections -arrow B-.
VW UP. 5 Gang-Schaltgetriebe 0CF

Check sheet metal ring

- Check the sheet metal ring in the clutch pressure plate -arrow- for damage.

  • Replace clutch pressure plates with broken sheet metal ring.
VW UP. 5 Gang-Schaltgetriebe 0CF

Center clutch disc

- Tighten all bolts in small steps in a crisscross pattern.

- Install the transmission.

Tightening torques

  • Pressure plate to flywheel
VW UP. 5 Gang-Schaltgetriebe 0CF