Body

Exterior Rearview Mirror

~4min read
0102030405064N·mlb·ft
Tightening torque found on this page

Overview - Exterior Rearview Mirror

Overview - Exterior Rearview Mirror

1 - Mirror Glass

  • Removing and installing. Refer to → Chapter "Mirror Glass, Removing and Installing".

2 - Exterior Rearview Mirror Housing

  • Removing and installing. Refer to → Chapter "Mirror Cap, Removing and Installing".

3 - Mirror cap

  • for the mirror adjusting unit mount
  • Removing and installing. Refer to → Chapter "Exterior Rearview Mirror Cover, Removing and Installing".

4 - Mirror Adjusting Unit

  • Removing and installing. Refer to → Chapter "Mirror Adjusting Unit, Removing and Installing".

5 - Bolt

  • Quantity: 2
  • Tightening specification. Refer to → Electrical Equipment; Rep. Gr.94; Exterior Rearview Mirror Lamps; Overview - Exterior Rearview Mirror Lamps.

6 - Exterior Mirror Turn Signal Lamp

  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.94; Exterior Rearview Mirror Lamps; Driver/Front Passenger Exterior Rearview Mirror Turn Signal Bulb L131/L132, Removing and Installing.

7 - Lane Change Assistance Warning Lamp inside the Exterior Mirror

  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.96; Lane Change Assistance; Lane Change Assistance Warning Lamp In Driver/Front Passenger Exterior Rearview Mirror K233/K234, Removing and Installing.

8 - Mirror Adjusting Unit Mount

  • Common part with cover
  • Removing and installing. Refer to → Chapter "Exterior Rearview Mirror, Removing and Installing".

9 - Seal

  • For the mirror base

10 - Bolt

  • 6 N·m
  • Quantity: 3

11 - Bolt

  • 1 N·m

Exterior Rearview Mirror, Removing and Installing

Exterior Rearview Mirror, Removing and Installing

Removing

- Remove the window frame trim panel. Refer to → Body Interior; Rep. Gr.70; Front Door Trim Panels; Window Frame Trim, Removing and Installing.

- Pull the retainer -1- and press the release to disconnect the connector -2-.

- Disconnect the connector -6-.

- Remove the plugs -4 and 5-.

- Remove the bolts -arrows-.

- Remove the mirror adjusting unit mount while guiding the grommet -4- and the wiring harness -3- out through the body opening.

Installing

Install in reverse order of removal. Note the following:

- For vehicles with the peripheral camera, the peripheral camera must be recalibrated. Refer to → Communication; Rep. Gr.91; Peripheral Camera; Component Location Overview - Peripheral Camera.

A66-10911

Exterior Rearview Mirror Cover, Removing and Installing

Removing

- Remove the exterior rearview mirror housing. Refer to → Chapter "Mirror Cap, Removing and Installing".

- Push the bracket -5- slightly to the side and remove the connector -4- from the mount.

- For vehicles with a peripheral camera system, disconnect the connector.

- Release the tabs -1-.

- Remove the cover -2- for the mirror adjustment unit mount in direction of -arrow- from the mirror adjustment unit mount -3-.

Installing

Install in reverse order of removal. Note the following:

- For vehicles with the peripheral camera, the peripheral camera must be recalibrated. Refer to → Communication; Rep. Gr.91; Peripheral Camera; Component Location Overview - Peripheral Camera.

A66-10910

Mirror Glass, Removing and Installing

Special tools and workshop equipment required

  • Double Suction Lifter -VAG1344-
  • Safety Gloves

Removing

WARNING

Risk of injury.

Wear safety gloves.

- Position the Double Suction Lifter -VAG1344- on the center of the mirror glass -1-, as illustrated.

- Remove the mirror glass from the mirror adjuster using the Double Suction Lifter - VAG1344-.

A66-10656

- Disconnect the connectors -1 and 2- for the mirror heating on the back of the mirror glass -3-.

- Unclip the connector -4- (if equipped) from the bracket -arrow-.

Installing

Install in reverse order of removal. Note the following:

- Position the mirror glass on the mirror adjusting unit and press it on.

Note

Only press the center of the mirror glass when pressing it on.

A66-10652

Mirror Adjusting Unit, Removing and Installing

Removing

- Remove the mirror glass. Refer to → Chapter "Mirror Glass, Removing and Installing".

- Remove the bolt -1-.

- Disengage the mirror adjuster -2- from the mount -arrow-.

- Disconnect the connector -3- from the mirror adjuster.

- Remove the mirror adjuster.

Installing

Install in reverse order of removal. Note the following:

- Press the mirror adjusting unit onto the mirror mount until it engages audibly.

A66-10857

Mirror Cap, Removing and Installing

Removing

- Remove the mirror glass. Refer to → Chapter "Mirror Glass, Removing and Installing".

- Remove bolts -4- and -5-.

- Open the four tabs -3-.

- Remove the exterior rearview mirror housing -2- from the cover -1--arrows-.

- If the vehicle has lane change assistance, disconnect the connector -6- for the lane change assistance warning lamp.

- Remove the exterior rearview mirror housing upward and disconnect the connector from the turn signal bulb.

- If the housing is replaced, remove the turn signal bulb. Refer to → Electrical Equipment; Rep. Gr.94; Exterior Rearview Mirror Lamps; Driver/Front Passenger Exterior Rearview Mirror Turn Signal Bulb L131/L132, Removing and Installing.

Installing

Install in reverse order of removal. Note the following:

- Tighten the screws on the housing mounting to 2 N·m.

A66-10974