Body

Overview - Sill Panel Trim

~4min read
0102030405086N·mlb·ft
Tightening torque found on this page
Overview - Sill Panel Trim

1 - Front Sill Panel Strip

  • There are different versions. Refer to the Parts Catalog.
  • Removing and installing. Refer to → Chapter "Sill Panel Trim, Removing and Installing".

2 - Rear Sill Panel Strip

  • There are different versions. Refer to the Parts Catalog.
  • Removing and installing. Refer to → Chapter "Sill Panel Trim, Removing and Installing".

Overview - Sill Panel Trim

Overview - Sill Panel Trim

Overview - Sill Panel Trim

1 - Front Cover

  • For vehicle lift point

2 - Quick Release

  • Quantity: 7

3 - Front Mount

  • For the quick release
  • Quantity: 3
  • Removing and installing. Refer to → Chapter "Front and Rear Quick Release Mount, Removing and Installing".

4 - Trim

  • For the sill panel trim
  • Removing and installing. Refer to → Chapter "Trim Piece for Sill Panel Trim, Removing and Installing".

5 - Expanding Clip

  • Quantity: 4

6 - Bolt

  • 8 N·m

7 - Front Bracket

  • For the sill panel trim
  • Removing and installing. Refer to → Chapter "Front Bracket for Sill Panel Trim, Removing and Installing".

8 - Front Sill Panel Strip

9 - Rear Bracket

  • For the sill panel trim
  • Quantity: 9
  • Removing and installing. Refer to → Chapter "Rear Bracket for Sill Panel Trim, Removing and Installing".

10 - Rear Sill Panel Strip

11 - Rear Mount

  • For the quick release
  • Quantity: 4
  • Removing and installing. Refer to → Chapter "Front and Rear Quick Release Mount, Removing and Installing".

12 - Quick Release

13 - Sill Panel Trim

  • Removing and installing. Refer to → Chapter "Sill Panel Trim, Removing and Installing".

14 - Rear Cover

  • For vehicle lift point

Overview - Sill Panel Trim, allroad

Overview - Sill Panel Trim, allroad

1 - Sill Panel Trim

  • Removing

- Turn the twist locks 90º and remove.

- Pull the sill panel trim at the bottom of the A-pillar out of the bracket.

- Warm the sill panel trim at the C-pillar with a hot air gun and carefully loosen the two-side tape.

- Unclip the sill panel trim one clip after the other and remove it.

  • Installing

- Remove the chafe protection and the two-sided tape when installing, if necessary.

- Clean the area where the two-side tape is going to be used with Cleaning Solution -D 009 401 04-.

- Position the rear sill panel trim using the centering pin and then push it into the bracket.

- Push the sill panel trim into the sill panel clips -6- starting from the rear and working forward.

- Install the twist locks -8-.

- Press the adhesive surface for the two-side tape using the Roller -3356-.

2 - Clip

- Install in the sill panel.

3 - Bracket

4 - Fitting Bolt

  • 8 N·m

5 - Nut

6 - Clip

- Replace any clips that get damaged while removing.

- Install on the sill panel trim as illustrated.

7 - Sill Panel

8 - Twist Lock

- Turn 90º and remove.

- Press in to install.

Overview - Sill Panel Trim, Sill Panel, allroad

Overview - Sill Panel Trim, Sill Panel, allroad

1 - Bolt

  • 2,5 N·m

2 - Sill Panel Trim

Note

It is not possible to remove the sill panel trim without damaging it. It must be replaced.

  • Removing

- Remove the screws and then warm the surfaces on the sill panel strip where the adhesive is with a hot air gun.

- Remove the sill panel strip.

- Remove any remaining adhesive on the sill panel trim completely.

  • Installing

- Clean the adhesive surfaces using Cleaning Solution -D 009 401 04-.

- Remove the peel-off backing from the tape.

- Insert the sill panel strip into the opening and then push on it.

- Press the sill panel strip using Roller -3356-.

- Tighten bolts to tightening specification.

3 - Grommet

4 - Upper Tape

- For the sill panel strip

5 - Lower Tap

- For the sill panel strip

6 - Sill Panel Trim