Body

Foot Rest, Removing and Installing

~5min read

Special tools and workshop equipment required

  • Trim Removal Wedge -3409-

Removing

- Remove the instrument panel cover on the driver side. Refer to → Chapter "Driver Side Instrument Panel Cover, Removing and Installing".

- Remove the front driver side sill panel trim. Refer to → Chapter "Front Sill Panel Strip, Removing and Installing".

- Unclip the foot rest -1- using the Trim Removal Wedge -3409--arrow- and remove.

Installing

Install in reverse order of removal. Note the following:

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Foot Rest and Carpet".

A70-10811

Carpet, Removing and Installing

Removing

- Remove the front seats. Refer to → Chapter "Front Seat, Removing and Installing".

- Remove the rear bench seat. Refer to → Chapter "Seat Bench/Single Seat, Removing and Installing".

- Remove the lower B-pillar trim panel. Refer to → Chapter "Lower B-Pillar Trim Panel, Removing and Installing".

- Remove the front sill panel strip. Refer to → Chapter "Front Sill Panel Strip, Removing and Installing".

- Remove the rear sill panel strip. Refer to → Chapter "Rear Sill Panel Strip, Removing and Installing".

- Remove the glove compartment. Refer to → Chapter "Glove Compartment, Removing and Installing".

- Remove the instrument panel cover on the driver side. Refer to → Chapter "Driver Side Instrument Panel Cover, Removing and Installing".

- Remove the center console. Refer to → Chapter "Center Console, Removing and Installing".

- Remove the front footwell cover. Refer to → Chapter "Front Footwell Cover, Removing and Installing".

- Remove the center console bracket and lower the shift mechanism. Refer to → Chapter "Center Console Bracket, Removing and Installing".

- Remove the rear air guide channel. Refer to → Heating, Ventilation and Air Conditioning; Rep. Gr.87; Air Guide; Air Distribution Channels, Removing and Installing.

- Remove the floor mat.

- Disengage the floor covering at brackets -1 and 2-.

- Pull the floor covering -3- back.

Note

Make sure the floor covering does not tear at the openings.

- Fold floor covering together and remove it through the rear door.

Installing

- Fold floor covering and lay it in the vehicle.

- Push floor covering forward and align it so that the openings align.

Installation is performed in reverse order of removal, noting the following:

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Foot Rest and Carpet".

A70-10660

Rear Shelf, Removing and Installing

Special tools and workshop equipment required

  • Pry Lever -80-200-
  • Omega Clip Tool -T40280-

Removing

- Versions with foldable rear seat backrest: for the rear seat backrest forward.

- For vehicles with a fixed rear seat backrest: remove the rear seat backrest. Refer to → Chapter "Rear Seat Backrest, Removing and Installing".

- For vehicles with a Multi-contour seat: remove the Multi-contour seat. Refer to → Chapter "Rear Seat Backrest, Removing and Installing, Multi-contour Seat".

- Remove the rear center belt guide. Refer to → Chapter "Rear Seat Belt Guide, Removing and Installing".

- Remove the center rear belt end fitting. Refer to → Chapter "Rear Seat Belt Latch, Removing and Installing".

- Remove the D-pillar trim panel. Refer to → Chapter "D-Pillar Trim, Removing and Installing, Sedan".

Vehicles with A Sound System

- Remove the speaker trim on the left side on the rear shelf. Refer to → Chapter "Speaker Trim, Removing and Installing".

- Remove the bolts -1 and 2-.

A70-11681

- Remove the bolt -1- for the rear shelf in the luggage compartment.

A70-11682

Versions with a Sun Shade

- Unclip the front rear shelf -1- using the Pry Lever -80-200- in direction of -A arrows-.

- Detach the rear shelf in the back of the sun shade in direction of -B arrows- and remove it by pulling it toward the front.

A70-11684

Vehicle Versions without Sun Shade

- Unclip the front rear shelf -1- using the Pry Lever -80-200- in direction of -A arrows-.

- Pull the rear shelf forward out of its mount in the rear window frame in direction of -arrow B- and remove.

A70-11683

Installing

Install in reverse order of removal. Note the following:

- Insert the rear shelf -1- into the rear window frame and tighten the screws.

  • The pins on the rear shelf must catch on the holding mounts and remain in place -arrow- on the rear window frame.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Rear Shelf".

A70-11497

Speaker Trim, Removing and Installing

Note

Be extremely careful when removing and installing because it is easy to damage the speaker trim.

Special tools and workshop equipment required

  • Wedge Set -T10383-

Removing

- Versions with foldable rear seat backrest: for the rear seat backrest forward.

- Use the wedge Wedge Set -T10383/1- or a screwdriver to carefully unclip front and sides of the speaker trim -1- along the seam for the rear shelf in direction of -arrow-.

- Vehicles equipped with a speaker: disconnect the electrical connector and remove the speaker trim in a forward direction.

Installing

Install in reverse order of removal. Note the following:

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Rear Shelf".

A70-10821