Transmission

Left Seal, Replacing

~3min read

Left Seal, Replacing, 0BC

  • In this chapter "right seal, replacing" is also described.
  • The shaft seal can be only be replaced with the final drive removed.

Special tools and workshop equipment required

  • Puller - Flanged Shaft -T10037-
  • Bearing/Bushing Installer - Multiple Use -VW295-
  • Seal Installer - Flange Shaft -T40108-
  • Sealing Grease -G 052 128 A1-

Removing

- Follow all general repair information. Refer to → Chapter "Repair Information".

- Remove the rear final drive. Refer to → Chapter "Final Drive, Removing and Installing".

Remove the Right Flange Shaft.

- Attach the Puller - Flanged Shaft -T10037- to the housing -arrow- and remove the flange shaft.

A39-10264

Left Flange Shaft, Removing

- Attach the Puller - Flanged Shaft -T10037- to the housing -arrow- and remove the flange shaft.

A39-10263

- Use a suitable tool to pry out the seal.

Installing

Install in reverse order of removal. Note the following:

A39-0373

Right Shaft Seal, Installing

- Coat outer edge of the seal with gear oil.

- Fill the space between the sealing/dust lip halfway with Sealing Grease -G 052 128 A1-.

- Drive in new shaft seal as far as stop without tilting it.

A39-10096

Left Shaft Seal, Installing

- Coat outer edge of the seal with gear oil.

- Fill the space between the sealing/dust lip halfway with Sealing Grease -G 052 128 A1-.

- Drive in new shaft seal as far as stop without tilting it.

A39-10097

Right and Left Flange Shafts, Installing

- Drive the flange shaft in using a Bearing/Bushing Installer - Multiple Use -VW295-.

- Install the rear final drive. Refer to → Chapter "Final Drive, Removing and Installing".

- Check the gear oil in rear final drive. Refer to → Chapter "Gear Oil, Checking Level, 0BC".

A39-10095

Left Seal, Replacing, 0BE, 0BF

  • In this chapter "right seal, replacing" is also described.
  • The shaft seal can be only be replaced with the final drive removed.

Special tools and workshop equipment required

  • Slide Hammer Set -VW771-
  • Seal Installer - Drift Shaft -T40221-
  • ATF

Removing

- Follow all general repair information. Refer to → Chapter "Repair Information".

- Remove the rear final drive. Refer to → Chapter "Final Drive, Removing and Installing".

- Remove the flange shaft bolt. To do this, install two bolts into the flange and counterhold the flange shaft using an assembly lever.

- Remove the flange shaft.

Note

If it not possible to remove the flange shaft by hand, then use the Slide Hammer Set -VW771- to remove it.

A39-10380

- Remove flange shaft seal with the Slide Hammer Set -VW771- and Slide Hammer Set - Pulling Hook -VW771/37-.

Installing

Install in reverse order of removal. Note the following:

A39-10381

Right Shaft Seal, Installing

- Coat the outer circumference and the sealing lips on the shaft seal with ATF.

- Install the shaft seal all the way. Be careful not to bend it.

A39-10382

Left Shaft Seal, Installing

- Coat the outer circumference and the sealing lips on the shaft seal with ATF.

- Install the shaft seal all the way. Be careful not to bend it.

- Install the flange shaft.

Note

If it is not possible to install the flange shaft all the way in by hand, then use a plastic mallet.

- Tighten the new flange shaft bolt to the tightening specification. Refer to -item 1-.

- Install the rear final drive. Refer to → Chapter "Final Drive, Removing and Installing".

- Check the ATF level in the rear final drive. Refer to → Chapter "ATF Level, Checking, 0BE, 0BF".

A39-10383

Right Seal, Replacing

Note

Replacing the right seal is described in the chapter "left seal, replacing".