Hyundai Palisade Quiz
Engine Mechanical System

Engine Mounting

In this manual: Engine Mechanical System
General Information — 10Engine Mechanical System — 56Engine Electrical System — 28Emission Control System — 21Engine Control System/Fuel System — 42Automatic Transmission System (A8LF1) — 33All-Wheel Drive (AWD) System — 16Drive Shaft and Axle — 19Suspension System — 28Steering — 17Restraints — 20Brake System — 39Body (Interior and Exterior) — 142Body Electrical System — 171Heating, Ventilation, and Air Conditioning — 47Advanced Driver Assistance System (ADAS) — 44
22steps
~132min
4/5difficulty
04080120160200117.787N·mlb·ft
Tightening torque found on this page
Done 0 of 22

Components and Component Location

Components

Hyundai Palisade. Components and components location
1. Transaxle Mount Bracket
2. Roller Rod Bracket
3. Engine Mount Bracket		 4. Engine mount bracket
5. Upper steering tie rod bracket

Hyundai Palisade. Components and components location

Repair Procedures

Removal and Installation

Hyundai Palisade. Repair procedures
  • Be careful not to damage parts located under the vehicle (floor under cover, fuel filter, fuel tank, and canister) when lifting the vehicle with a lift. (Refer to General Information - Jack Lifting Points and Support Points)

[Engine Mount]

  1. Remove the engine cover. (Refer to Engine and Transaxle Assembly - Engine Cover)
  2. Place a jack on the edge of the oil pan (A) to support the engine.
    Hyundai Palisade. Repair procedures
    Hyundai Palisade. Repair procedures
    • Insert a rubber block between the jack and the oil pan.
  3. Remove the engine mount support bracket (A).

    Tightening torque: 98.1–118 N·m

    Hyundai Palisade. Repair procedures
  4. Remove the engine mounting bracket (A).

    Tightening torque: 63.7–83 N·m

    Hyundai Palisade. Repair procedures
  5. Install in the reverse order of removal.

[Tie Rod Bracket]

  1. Remove the engine cover. (Refer to Engine and Transaxle Assembly - Engine Cover)
  2. Remove the roller rod bracket (A). Tightening torque: Bolt (B): 107.9–128 N·m Bolts (C): 49.0–64 N·m
    Hyundai Palisade. Repair procedures
  3. Remove the roller rod bracket (A).

    Tightening Torque: 49.0–69 N·m

    Hyundai Palisade. Repair procedures
  4. Install in the reverse order of removal.

[Transmission Mount]

  1. Disconnect the negative battery cable.
  2. Remove the air duct. (Refer to Intake and Exhaust System - Air Cleaner)
  3. Disconnect the positive battery terminal.
  4. Remove the air cleaner assembly. (Refer to Air Intake and Exhaust System - "Air Cleaner").
  5. Remove the battery and battery tray. (Refer to Engine Electrical System - "Battery")
  6. Remove the engine control module (ECM). (Refer to Engine Control/Fuel System - "Engine Control Module (ECM)").
  7. Remove the engine cover. (Refer to Engine and Transaxle Assembly - Engine Cover)
  8. Place a jack under the transaxle to support it.
    Hyundai Palisade. Repair procedures
    • Insert a rubber pad between the jack and the transmission.
  9. Remove the service cover (A).
    Hyundai Palisade. Repair procedures
  10. Remove the bolts securing the transaxle support bracket (A).

    Tightening torque: 107.9–128 N·m

    Hyundai Palisade. Repair procedures
  11. Remove the air cleaner bracket (A).

    Tightening torque: 7.8–9.8 N·m

  12. Remove the transmission mounting bracket (B).

    Tightening torque: 63.7–83 N·m

    Hyundai Palisade. Repair procedures
  13. Install in the reverse order of removal.

Test yourself

A quick Hyundai Palisade quiz: every answer comes with an explanation and a link to the manual page.