Differential Assembly
Exploded View

| Drive pinion lock nut | Companion flange | Front oil seal | |||
| Pinion front bearing | Collapsible spacer | Gasket | |||
| Filler plug | Drain plug | Mounting insulator | |||
| Gear carrier | Mounting insulator | Breather connector | |||
| Side shaft bearing | Snap ring | Snap ring | |||
| Side oil seal | Side shaft | Pinion rear bearing | |||
| Pinion height adjusting washer | Drive pinion | Drive gear | |||
| Differential assembly | Carrier cover | Bearing cap | |||
| Side bearing | Side bearing adjusting washer | Spacer | |||
| Side oil seal | |||||
| Screw hole | Comply with the assembly procedure when tightening. Refer to Disassembly and Assembly. | ||||
Disassembly and Assembly
DISASSEMBLY
Remove mounting insulators with drift [SST: ST33200000 (NI-26082)] if necessary.
Remove side shaft assembly. Refer to Disassembly and Assembly.
Remove side oil seal from gear carrier with a oil seal remover (commercial service tool).
For proper reinstallation, paint matching marks
on one side of bearing cap.

Remove bearing caps.

Lift the differential assembly out of the gear carrier with sliding hammer (A) (commercial service tool).

Remove differential assembly together with side bearing outer races and side bearing adjusting washers.

Remove spacer.
Remove side bearing inner races, using puller (A) and the base (B).

| A | : Puller [SST: ST33051001 (NI-22888-20)] |
| B | : Base [SST: ST33061000 (NI-8107-2)] |
For proper reinstallation, paint matching marks
on one differential assembly and drive gear.

Remove drive gear mounting bolts and then remove drive gear from differential assembly.
Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
Apply thread locking sealant into the thread hole of drive gear.

For applying thread locking sealant, refer to Exploded View.
Install the drive gear to differential assembly.
Tighten the drive gear mounting bolts with the following procedure.Tighten the bolts in a crisscross fashion to the specified torque.

| Drive gear mounting bolt tightening torque | : 59 N·m |

| Drive gear mounting bolt tightening angle | : 32 to 37 degree |
Press side bearing inner races to differential assembly, using the drift (A) and the base (B).

| A | : Drift [SST: ST33230000 (NI-35867)] |
| B | : Base [SST: ST33061000 (NI-8107-2)] |
Install spacer.
Install the differential case assembly with the side bearing outer races into the gear carrier.

Insert left and right original side bearing adjusting washers in place between side bearings and gear carrier.

Install the side bearing caps with the matching marks
aligned and tighten the side bearing cap bolts to the specified torque.

Install side oil seal until it becomes flush with the gear carrier with the drift (A and B).

| A | : Drift [SST: ST30720000 (NI-25405)] |
| B | : Drift [SST: ST27863000 ( — )] |
Check and adjust drive gear runout, tooth contact, backlash, and total preload torque. Refer to Adjustment.
Apply liquid gasket to mating surface of rear cover.

For applying liquid gasket, refer to Exploded View.
Install the carrier cover to the gear carrier. Tighten the bolts to the specified torque.
For tightening torque, refer to Exploded View.
Install side shaft assembly. Refer to Disassembly and Assembly.
Install mounting insulators with drift [SST: ST33200000 (NI-26082)].
Adjustment
TOTAL PRELOAD TORQUE
Remove side shaft. Refer to Disassembly and Assembly.
Rotate drive pinion back and forth 2 to 3 times to check for unusual noise and rotation malfunction.
Rotate drive pinion at least 20 times to check for smooth operation of the bearing.
Measure total preload with the preload gauge (A) [SST: ST3127S000 (NI-25765-A)].

| Total preload torque | : Refer to Preload Torque. |
If measured value is out of the specification, disassemble it to check and adjust each part. Adjust the pinion bearing preload and side bearing preload.
Adjust the pinion bearing preload first, then adjust the side bearing preload.
When the preload torque is large On pinion bearings: Replace the collapsible spacer. On side bearings: Use thinner side bearing adjusting washers by the same amount to each side. For selecting adjusting washer, refer to the latest parts information. When the preload is small On pinion bearings: Tighten the drive pinion lock nut. On side bearings: Tighten side bearing adjusting nut.
Use thicker side bearing adjusting washers by the same amount to each side. For selecting adjusting washer, refer to the latest parts information.
DRIVE GEAR RUNOUT
Remove carrier cover. Refer to Disassembly and Assembly.
Fit a dial indicator to the drive gear back face.
Rotate the drive gear to measure runout.

| Drive gear back face runout | : Refer to Drive Gear Runout. |
If the runout is outside of the repair limit, check drive gear assembly condition; foreign material may be caught between drive gear and differential case, or differential case or drive gear may be deformed, etc.
TOOTH CONTACT
Remove carrier cover. Refer to Disassembly and Assembly.
Apply red lead or equivalent to drive gear.

Rotate drive gear back and forth several times, check drive pinion gear to drive gear tooth contact.

Tooth Contact Judgment Guide
If tooth contact is improperly adjusted, follow the procedure below to adjust the pinion height (dimension X).

If the tooth contact is near the face (face contact), or near the heel (heel contact), thicken pinion height adjusting washer to move drive pinion closer to drive gear.

For selecting adjusting washer, refer to the latest parts information.
If the tooth contact is near the flank (flank contact), or near the toe (toe contact), thin pinion height adjusting washer to move drive pinion farther from drive gear.

For selecting adjusting washer, refer to the latest parts information.
BACKLASH
Remove carrier cover. Refer to Disassembly and Assembly.
Fit a dial indicator to the drive gear face to measure the backlash.

| Backlash | : Refer to Backlash. |
If the backlash is outside of the specified value, adjust with the side bearing adjusting nut.
When the backlash is large: Make drive gear back side adjusting washer thicker, and drive gear tooth side adjusting washer thinner by the same amount. For selecting adjusting washer, refer to the latest parts information. When the backlash is small: Make drive gear back side adjusting washer thinner, and drive gear tooth side adjusting washer thicker by the same amount. For selecting adjusting washer, refer to the latest parts information.
Inspection
INSPECTION AFTER DISASSEMBLY
Drive Gear and Drive Pinion
Clean up the disassembled parts.
If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.
If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive gear and drive pinion as a set.
Oil Seal
Whenever disassembled, replace.
If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.
Differential Assembly
Clean up the disassembled parts.
If any wear or crack is found, replace.