Suspension

Front Shock Absorber

3steps
~18min
5/5difficulty
Done 0 of 3

Exploded View

WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Piston rod lock nut Mounting insulator Rubber seat
Coil spring Dust cover Bound bumper
Shock absorber Lower link
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)

WITH DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Bracket Shock absorber harness Lower link
Shock absorber (With Built In Air Spring) Air adapter Air connector
Air tube
To air suspension control module
: Always replace after every disassembly.
: Apply silicone sealant.
: vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)

Removal and Installation

REMOVAL

Without Dynamic Digital Suspension and Electronic Air Suspension

Remove tires. Refer to ROAD WHEEL TIRE : Removal & Installation.

Set suitable jack under lower link.

Remove brake hose bracket from steering knuckle. Refer to Removal and Installation.

Separate upper link from steering knuckle.

  • 2WD models: Refer to Removal and Installation.

  • 4WD models: Refer to Removal and Installation.

Remove shock absorber mounting nuts (upper side).

Remove shock absorber mounting bolt (lower side), and remove shock absorber from vehicle.

Perform inspection after removal. Refer to Inspection.

With Dynamic Digital Suspension and Electronic Air Suspension

Start engine.

Turn auto height mode control switch to ON, shift the shift position to N and set to normal height.

Turn OFF the electronic air suspension function. Refer to Operation.

Stop engine.

Lift up the vehicle.

Remove tires. Refer to ROAD WHEEL TIRE : Removal & Installation.

Set suitable jack (A) under lower link.

Disconnect shock absorber harness connector , and remove shock absorber harness and bracket from vehicle.

Remove silicone sealant between the air connector and air adapter .

Apply the matching marks to the air tube when replacing air connector .

Loosen the air connector and perform air bleeding.

When reusing the air connector, remove air tube together with air connector from air adapter .

When replacing the air connector, follow the procedure below.Slide the air connector part to direction , and remove the part from the air tube .

Remove the air connector part from the air tube .

Remove air adapter from shock absorber if necessary.

Remove brake hose bracket from steering knuckle. Refer to Removal and Installation.

Separate upper link from steering knuckle.

  • 2WD: Refer to Removal and Installation.

  • 4WD: Refer to Removal and Installation.

Remove shock absorber mounting nuts (upper side).

Remove shock absorber mounting bolt (lower side), and remove shock absorber from vehicle.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Without Dynamic Digital Suspension and Electronic Air Suspension

Note the following, and install in the reverse order of removal.

  • Perform final tighting of shock absorber (lower side) by the following procedures.

    1. Measure between wheel center and fender arch (A).

    2. Set the wheel chocks on the rear tires.

    3. Jack up front of the vehicle and set the rigid rack.

    4. Remove the front tires.

    5. Set suitable jack (A) on the left and right steering knuckles (lower link ball joint fastening part).

    6. Jack up the left and right steering knuckles until the vehicle no longer floats off the rigid rack (A).

    7. Measure between wheel center and fender arch (A).

    8. Tight the mounting bolt of shock absorber (lower side) to the specified torque. Refer to Exploded View.

  • Perform inspection after installation. Refer to Inspection.

  • Perform adjustment after installation. Refer to Adjustment.

  • After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber. Refer to Disposal.

With Dynamic Digital Suspension and Electronic Air Suspension

Install shock absorber to vehicle.

Install shock absorber harness connector, shock absorber harness, and bracket.

Install upper link to steering knuckle.

  • 2WD: Refer to Removal and Installation.

  • 4WD: Refer to Removal and Installation.

Install brake hose bracket to steering knuckle. Refer to Removal and Installation.

Install air adapter to shock absorber if necessary.

When reusing the air connector, install air tube and air connector together to air adapter .

When replacing the air connector, follow the procedure below.Install air connector to air adapter .

Insert the air tube straight into the air connector to the marked point which is applied when removing.

Apply silicone sealant to faces air connector and air adapter .

Start engine.

Use CONSULT and fill the inner pressure of shock absorber to 5.7 bar. Refer to Work Support.

Stop engine.

Install tire. Refer to ROAD WHEEL TIRE : Exploded View.

Lift down the vehicle.

Start engine.

Perform pressure measurements using CONSULT. Refer to Work Support.

Use CONSULT and vehicle to the normal height. Refer to Work Support.

Turn ON the electronic air suspension function. Refer to Operation.

Stop engine.

Perform final tighting of shock absorber (lower side) by the following procedures.Measure between wheel center and fender arch (A).

Set the wheel chocks on the rear tires. Jack up front of the vehicle and set the rigid rack. Remove the front tires. Set suitable jack (A) on the left and right steering knuckles (lower link ball joint fastening part).
Jack up the left and right steering knuckles until the vehicle no longer floats off the rigid rack (A).
Measure between wheel center and fender arch (A).
Tight the mounting bolt of shock absorber (lower side) to the specified torque. Refer to Exploded View. Install front tire.

Perform inspection after installation. Refer to Inspection.

Perform adjustment after installation. Refer to Adjustment.

After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber. Refer to Disposal.

Disassembly & Assembly

DISASSEMBLY

Without Dynamic Digital Suspension and Electronic Air Suspension

Install shock absorber attachment [SST: ST35652000 ( − )] (A) to shock absorber and secure it in a vise.

Using a spring compressor (commercial service tool) (A), compress coil spring between rubber seat and shock absorber until coil spring with a spring compressor is free.

Check coil spring with a spring compressor between rubber seat and shock absorber is free. Remove piston rod lock nut while securing the piston rod tip so that piston rod does not turn.

Remove mounting insulator, rubber seat, dust cover, and bound bumper from shock absorber.

After removing coil spring with spring compressor (commercial service tool), gradually release the spring compressor.

Remove the shock absorber attachment [SST: ST35652000 ( − )] from shock absorber.

Perform inspection after disassembly. Refer to Inspection.

With Dynamic Digital Suspension and Electronic Air Suspension

ASSEMBLY

Without Dynamic Digital Suspension and Electronic Air Suspension

Install bound bumper to dust cover .

Install dust cover and bound bumper to mounting insulator .

Install shock absorber to bound bumper, dust cover, and mounting insulator.

Install shock absorber attachment [SST: ST35652000 ( − )] to shock absorber and secure it in a vise.

Compress coil spring using a spring compressor (commercial service tool), and install it onto shock absorber.

Align and attach the protrusions of the rubber sheet to the bolts of the mounting insulator .

Install rubber sheet and mounting insulator to shock absorber.

  • Install the mounting insulator as shown in the figure.

    Angle (A) : 90°
    : mounting insulator bolt
    : lower end of the coil spring
  • Align the lower end of the coil spring with the position (A) of the shock absorber in the diagram.

    A : 5 mm or less

Secure piston rod tip so that piston rod does not turn, then tighten piston rod lock nut to the specified torque.

Gradually release a spring compressor (commercial service tool), and remove coil spring.

Remove the shock absorber attachment [SST: ST35652000 ( − )] from shock absorber.

Inspection

WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Inspection After Removal

Check shock absorber for oil leakage or other malfunctions. Replace it if necessary.

Inspection After Installation

Check wheel alignment. Refer to Inspection.

WITH DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Inspection After Removal

Check shock absorber for oil leakage or other malfunctions. Replace it if necessary.

Inspection After Installation

  • Make sure the electronic air suspension function is turn ON. Refer to Operation.

  • Confirm that no warning message is displayed on the information display. Refer to Air suspension warning.

  • Perform the self-diagnosis with CONSULT. Check if any DTC is detected. Refer to CONSULT Function.

  • Confirm to close the hood.

  • Always check for the air leakage with soapy water.

  • Check wheel alignment. Refer to Inspection.

Adjustment

WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Adjustment After Installation

Adjust neutral position of steering angle sensor. Refer to Work Procedure.

WITH DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Adjustment After Installation

Adjust neutral position of steering angle sensor. Refer to Work Procedure.

Disposal

  1. Set shock absorber horizontally with the piston rod fully extended.

  2. Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position () from top as shown in the figure to release gas gradually.

    A : 20 – 30 mm (0.79 – 1.18 in)
  3. Position the drilled hole downward and drain oil by moving the piston rod several times.