Suspension

Front Suspension Service Data and Specifications

~3min read
010203040506.45N·mlb·ft
Tightening torque found on this page

Wheel Alignment

WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

ItemStandard

Camber

Degree minute (Decimal degree)
Minimum −0°50′ (−0.83°)
Nominal −0°05′ (−0.08°)
Maximum 0°40′ (0.66°)
Left and right difference*1 –0° 33′ (–0.55°) - 0° 33′ (0.55°)

Caster

Degree minute (Decimal degree)
Minimum 3° 40′ (3.67°)
Nominal 4° 25′ (4.42°)
Maximum 5° 10′ (5.16°)
Left and right difference*1 –0° 45′ (–0.75°) - 0° 45′ (0.75°)

Kingpin inclination

Degree minute (Decimal degree)
Minimum —
Nominal 11°10′ (11.17°)
Maximum —
Toe-in

Total toe-in

Distance
Minimum Out 0.7 mm (Out 0.028 in)
Nominal In 1.3 mm (In 0.051 in)
Maximum In 3.3 mm (In 0.130 in)

Total toe-angle

Degree minute

(Decimal degree)
Minimum Out 0° 03′ (Out 0.05°)
Nominal In 0° 05′ (In 0.08°)
Maximum In 0° 13′ (In 0.21°)

Measure value under unladen*2 conditions.

*1: A difference when assuming the left side a standard.

*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

WITH DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

ItemStandard

Camber

Degree minute (Decimal degree)
Minimum −1°00′ (−1.00°)
Nominal −0°15′ (−0.25°)
Maximum 0°30′ (0.50°)
Left and right difference*1 –0° 33′ (–0.55°) - 0° 33′ (0.55°)

Caster

Degree minute (Decimal degree)
Minimum 4° 00′ (4.00°)
Nominal 4° 45′ (4.75°)
Maximum 5° 30′ (5.50°)
Left and right difference*1 –0° 45′ (–0.75°) - 0° 45′ (0.75°)

Kingpin inclination

Degree minute (Decimal degree)
Minimum —
Nominal 11°20′ (11.33°)
Maximum —
Toe-in

Total toe-in

Distance
Minimum Out 2.0 mm (Out 0.08 in)
Nominal 0.0 mm (0.0 in)
Maximum In 2.0 mm (In 0.08 in)

Total toe-angle

Degree minute

(Decimal degree)
Minimum Out 0° 08′ (Out 0.13°)
Nominal 0° 00′ (0.00°)
Maximum In 0° 08′ (In 0.13°)

Measure value under unladen*2 conditions.

*1: A difference when assuming the left side a standard.

*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Ball Joint

ItemStandard
Swing torque Lower link 0.5 – 6,4 N·m
Upper link 0.5 – 4,9 N·m
Measurement on spring balance (cotter pin hole position) Lower link 5.9 – 74.5 N (0.61 – 7.59 kg, 1.33 – 16.74 lb)
Upper link 7.6 – 74.3 N (0.78 – 7.57 kg, 1.71 – 16.70 lb)
Rotating torque Lower link 0.5 – 6,4 N·m
Upper link 0.5 – 4,9 N·m

Wheel Height

WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

Except for Canada

ItemStandard
Wheel size 18 inch 20 inch
Front (Hf) 929 mm (36.57 in) 937 mm (36.89 in)
Rear (Hr) 936 mm (36.85 in) 945 mm (37.20 in)

Measure value under unladen* conditions.

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

For Canada

ItemStandard
Wheel size 18 inch 20 inch
Front (Hf) 929 mm (36.57 in) 937 mm (36.89 in)
Rear (Hr) 936 mm (36.85 in) 944 mm (37.17 in)

Measure value under unladen* conditions.

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

WITH DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION

ItemStandard
Wheel size 18 inch 20 inch
Front (Hf) 928 mm (36.54 in) 928 mm (36.54 in)
Rear (Hr) 935 mm (36.81 in) 936 mm (36.85 in)

Measure value under unladen* conditions.

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.