Steering

Steering Shaft

2steps
~12min
5/5difficulty
Done 0 of 2

Exploded View

STEERING SHAFT

Steering shaft Lower joint Hole cover*
Clamp* Hole cover seal Collar
Upper joint
*: Replace and as a set.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)

Removal and Installation

Removal

Set vehicle to the straight-ahead position.

Fix the steering wheel.

Remove driver knee air bag module. Refer to Removal and Installation.

Remove steering shaft fixing bolt and nut , and separate lower joint from steering shaft .

Remove lower joint fixing fixing bolt , and remove lower joint from steering gear assembly .

Turn carpet and remove the hole cover mounting nuts.

Remove upper joint fixing bolt and nut , and separate steering shaft from upper joint .

Remove the steering shaft and hole cover assembly.

Remove collar, hole cover seal, and hole cover assembly.

Perform a post-removal inspection. Refer to Inspection.

Installation

Note the following, and install in the reverse order of removal.

  • Insert the hole cover seal into the steering shaft and install it until side of the hole cover seal and side of the hole cover come into contact.

  • Install clamp as shown in the figure.

    A : 90 degrees
    : vehicle front
  • Tighten the clamp and check the length (A).

    Clamp length (A) : 16 - 20 mm (0. 63 - 0.79 in)
  • Insert the collar into the steering shaft , make sure that the claws of the collar are not half-fitted into the grooves of the steering shaft, and that they are fully seated all the way.

    : OK
    : NG
  • After tightening the upper joint fixing bolt and nut , check the no clearance between steering shaft , bolt and upper joint .

  • When installing lower joint, tighten the steering gear side fixing bolt first.

  • When installing the lower joint to steering gear assembly, perform the following procedure.

  1. After aligning the blocking phase of pinion, the lower joint shall be inserted to the pinion shaft of steering gear assembly until lower joint lower surface is in contact with pinion shaft of steering gear assembly surface .

  2. Insert bolt to lower joint , and tighten bolt to the specified torque.

    : Pinion shaft of steering gear assembly
  • When installing lower joint to steering shaft , check the fixing length (A).

    A : 15.9 - 21.9 mm (0.626 - 0.862 in)
  • After tightening the steering shaft fixing bolt and nut , check the no clearance between lower joint , bolt and steering shaft .

  • Perform a post-installation inspection. Refer to Inspection.

Inspection

INSPECTION AFTER REMOVAL

  • Check dust boot clamp (looseness and disconnection) and dust boot (scratches, cracks, and holes). Replace the lower joint, as necessary.

  • Check each part of lower joint for damage and other malfunctions. Replace if there is a malfunction.

  • Check each part of steering shaft for damage and other malfunctions. Replace if there is a malfunction.

  • Check steering shaft and hole cover seal for scratches, cracks, and holes. Replace the steering shaft or hole cover seal, as necessary.

  • Check the sliding range (A) of the lower joint.

Sliding range (A) : Refer to Steering Shaft.
  • Check the length (A) (extended position) of the lower joint.

    Lower joint length (A) : Refer to Steering Shaft.
  • Rotate the steering shaft to check runout of the steering shaft at the runout measuring point by using dial indicator and V-block.

Steering shaft runout : Refer to Steering Shaft.
B : 37.5 mm (1.476 in)
C : 75 mm (2.95 in)

INSPECTION AFTER INSTALLATION

  • Check dust boot bellows (deformation, such as dents). Manually rework the bellows, as necessary.

  • Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.

  • Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel turning angle.

  • Adjust neutral position of steering angle sensor. Refer to Work Procedure.

  • If equipped with ProPILOT Assist, perform steering torque calibration after replacing or removal and installation the steering wheel. Refer to Work Procedure.