Steering

Steering Gear and Linkage

~7min read

Exploded View

REMOVAL

Member Cotter pin Steering gear assembly
: vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

DISASSEMBLY

Outer socket Outer socket lock nut Boot clamp (small diameter)
Boot Boot clamp (large diameter) Inner socket
Gear housing assembly
: N·m (kg-m, ft-lb)
: Apply RheoGel TEK676.
: Always replace after every disassembly.
: vehicle front

Removal and Installation

REMOVAL

Set vehicle to the straight-ahead position.

Remove 12V battery terminal. Refer to Removal and Installation.

Remove tires. Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove cotter pins and mounting nuts, and separate outer socket from steering knuckle.

Remove outer sockets, outer socket lock nuts, boots, boot clamps, and Inner sockets if necessary. Refer to Disassembly and Assembly.

Remove front under cover. Refer to Removal and Installation.

Remove engine under cover. Refer to Removal and Installation.

Disconnect steering gear assembly harness connectors.

Remove harness clip from steering gear assembly.

Remove lower joint from steering gear assembly.

Remove air inlet tube 1. Refer to Removal & Installation.

Remove steering gear assembly mounting bolts and nuts.

Remove steering gear assembly from vehicle.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Before installation, check that the tilt position is at the middle level.

  • To install the steering gear assembly, after inserting the mounting bolts, temporarily tighten the mounting nuts using the tightening method and numerical order shown below, and then tighten to the specified torque.

    Temporary tightening : 1 → 2 → 3
    Final tightening (Specified torque) : 4 → 5 → 6
  • Perform final tightening of nuts and bolts on each part under unladen conditions with tires on level ground when removing steering gear assembly. Check wheel alignment.

  • Rotate steering wheel to check for decentered condition, binding, noise or excessive steering effort.

  • Perform inspection after installation. Refer to Inspection.

Disassembly and Assembly

DISASSEMBLY

Loosen outer socket lock nut, and remove outer socket.

Remove boot clamps, and then remove boot from inner socket and housing.

Remove the left inner socket.

Remove the right inner socket.

Perform inspection after disassembly. Refer to Inspection.

ASSEMBLY

Install left inner socket. Tighten to specified torque. Refer to Exploded View.

Install right inner socket. Tighten to specified torque. Refer to Exploded View.

Apply recommended grease to part of inner socket.

Use RheoGel TEK676.
B (groove part) : 0.2 mm (0.008 in)

Apply recommended grease to part of gear housing assembly.

Use RheoGel TEK676.
B : 4 mm (0.16 in)

Install boot to inner socket and gear housing.

Install boot clamp (large diameter) to boot using boot band crimping tool [SST: KV40107300 (NI-51751)] (A).

Install boot clamp (small diameter) to boot.

Adjust inner socket to standard length (A), and then tighten lock nut to the specified torque. Check length again after tightening lock nut.

: Outer socket
Inner socket length (A) : Steering Gear and Linkage

Inspection

INSPECTION AFTER DISASSEMBLY

Boot

  • Check boot for cracks, and replace it if a malfunction is detected.

Gear Housing Assembly

  • Check gear housing assembly for damage and scratches. Replace if there are any abnormal conditions.

Outer Socket and Inner Socket

  • Check the following items and replace the component if it does not meet the standard.

BALL JOINT SWINGING FORCE

  • Hook a pull gauge [SST: — (NI-44372)] at the point shown in the figure and pull the pull gauge. Make sure that the pull gauge reads the specified value when ball stud and inner socket start to move. Replace outer socket and inner socket if they are outside the standard.

    Measuring point of outer socket
    • Ball stud cotter pin hole

    • Moment arm length (B): 71.4 mm (2.811 in)

    Measuring point of inner socket
    • Point shown in the figure

    • Moment arm length (D): 108.4 mm (4.27 in)

    Swinging force : Refer to Steering Gear and Linkage

BALL JOINT ROTATING TORQUE

  • Make sure that the reading is within the following specified range using suitable tool (A). Replace outer socket if the reading is outside the specification.

    Rotating torque : Refer to Steering Gear and Linkage

BALL JOINT AXIAL END PLAY

  • Apply an axial load of 490 N (50 kg, 110 lb) to ball stud. Using a dial gauge, measure amount of stud movement, and then make sure that the value is within the following specified range. Replace outer socket and inner socket if the measured value is outside the standard.

    Axial end play : Steering Gear and Linkage

INSPECTION AFTER INSTALLATION

  • Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.

  • Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel turning angle.

    • Steering wheel play: Refer to Inspection.

    • Neutral position steering wheel, steering wheel turning force, and front wheel turning angle: Refer to Inspection.

  • Perform "ADDITIONAL SERVICE WHEN REPLACING POWER STEERING CONTROL MODULE". Refer to Work Procedure.

  • Adjust neutral position of steering angle sensor. Refer to Work Procedure.

  • If equipped with ProPILOT Assist, perform steering torque calibration after replacing or removal and installation the steering wheel. Refer to Work Procedure.