Body Exterior, Doors, Roof & Vehicle Security

Windshield Glass

~14min read

Exploded View

Windshield molding Dam sealant rubber upper Clip
Insulator Dam sealant rubber Spacer
Windshield glass Roof panel Adhesive
Painted surface primer Glass primer Body side outer panel
Dash panel
: Bracket
: Inside mirror base
: Edge
: R end
: Always replace after every disassembly.

Unit: mm (in)

PortionPrimer rangeAdhesive range
MNO
Windshield glass - Roof panel - G Between windshield molding and dam sealant rubber upper

0 + 1.0, - 0.0

(0.0 + 0.04, - 0.0)

7.0 + 2.0, - 0.0

(0.28 + 0.08, - 0.0)

12.0 + 2.0, - 0.0

(0.47 + 0.08, - 0.0)
H From R-end, more than 20.0 (0.79)
Windshield glass - Body side outer panel - I Between R-end and dam sealant rubber
J From body side panel edge, more than 15.4 (0.61)
Windshield glass - Dash panel - K From dam sealant rubber, more than 11.0 (0.43)
L From dash panel R-end, more than 19.0 (0.75)

Removal and Installation

REMOVAL

Replacement Windshield Glass

Remove inside mirror or intelligent rear view mirror. Refer to following.

  • Inside mirror : Removal and Installation.

  • Intelligent rear view mirror : Removal and Installation.

Remove front camera unit. Refer to Removal and Installation (with front camera unit).

Remove front camera (driving video recorder). Refer to Removal and Installation (with driving video recorder system).

Remove light & rain sensor. Refer to Removal and Installation (if equipped).

Remove headlining assembly. Refer to Removal and Installation.

Remove map lamp bracket. Refer to Removal and Installation.

Remove cowl top cover. Refer to Removal and Installation.

Remove front pillar finisher. Refer to Removal and Installation.

Disconnect windshield glass harness connector (if equipped).Disconnect windshield glass harness connectors .

  • Under the cowl top cover

  • Inside vehicle

Fix windshield glass harness by using tapes.

Apply protective tape (A) on roof panel and body side outer panel around windshield glass to protect painted surface from damage.

Insert a windshield cutter (A) between windshield glass and each panel . Cut the adhesive by pulling the windshield cutter, keeping the tip parallel to the edge of windshield glass.

Apply protective standish cover (A) on instrument panel to protect it from damage.

Cut the adhesive using a piano wire.Pass the piano wire (B) from passenger room to bonded area of windshield glass using a wire pierce (A).

Tie both ends of the piano wire (B) to the wire grip (A), etc.
To cut adhesive by using piano wire alongside of windshield glass and each panel.

Use suction lifter (A) to remove windshield glass from the vehicle.

Remove remaining clips, windshield molding, dam sealant rubbers, spacer, insulator from the vehicle.

Reuse Windshield Glass

Remove inside mirror or intelligent rear view mirror. Refer to following.

  • Inside mirror : Removal and Installation.

  • Intelligent rear view mirror : Removal and Installation.

Remove front camera unit. Refer to Removal and Installation (with front camera unit).

Remove front camera (driving video recorder). Refer to Removal and Installation (with driving video recorder system).

Remove light & rain sensor. Refer to Removal and Installation (if equipped).

Remove headlining assembly. Refer to Removal and Installation.

Remove map lamp bracket. Refer to Removal and Installation.

Remove cowl top cover. Refer to Removal and Installation.

Disconnect windshield glass harness connector (if equipped).Disconnect windshield glass harness connectors .

  • Under the cowl top cover

  • Inside vehicle

Fix windshield glass harness by using tapes.

Record clip install position.Apply protective tape (A) to record the clip install position.

Write matching marks (A) on protective tape as shown in the figure.

Apply protective tape (A) on roof panel and body side outer panel around windshield glass to protect painted surface from damage.

Apply matching marks to windshield glass, roof panel, and both side of body side outer panel.

Apply protective standish cover (A) on instrument panel to protect it from damage.

Cut the adhesive using a piano wire.Pass the piano wire (B) from passenger room to bonded area of windshield glass using a wire pierce (A).

Tie both ends of the piano wire (B) to the wire grip (A), etc.
To cut adhesive by using piano wire alongside of windshield glass and each panel.

Use suction lifter (A) to remove windshield glass from the vehicle.

Remove remaining clips, windshield molding, dam sealant rubbers, spacer, insulator from the vehicle.

INSTALLATION

Replacement Windshield Glass

Use a cutter knife or scraper, and leave the adhesive on the body side thin and smooth as shown in the figure.

Place new windshield glass on the vehicle temporarily, put on matching marks on windshield glass, roof panel, and both side of body side outer panel.

Use suction lifter (A) to set windshield glass on glass stand (B).

Clean the bonded area on windshield glass and body panel side using a white gasoline or degreasing agent.

Install dam sealant rubber upper.Clean windshield glass to install position of dam sealant rubber upper by using white gasoline or degreasing agent. Remove release liner of double-sided tape for installing dam sealant rubber upper. Install dam sealant rubber upper on windshield glass as shown in the figure.

Unit: mm (in)

* : ± 1.0 mm (0.04 in)
Edge
R-end

Install insulator.Clean windshield glass to install position of insulator by using white gasoline or degreasing agent. Remove release liner of double-sided tape for installing insulator. Install insulator on windshield glass as shown in the figure.

Unit: mm (in)

* : ± 2.0 mm (0.08 in)
Edge
Center
Vertex
H : Dimensions

Install dam sealant rubber.Clean windshield glass to install position of dam sealant rubber by using white gasoline or degreasing agent. Remove release liner of double-sided tape for installing dam sealant rubber. Install dam sealant rubber on windshield glass as shown in the figures.

  • Top left and right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Side left and right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Lower left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Bottom left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Bottom middle left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    : Upward
  • Bottom center left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Center
    Edge
    : Upward
  • Bottom center right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Center
    Edge
    : Upward
  • Bottom right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Lower right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    R-end
    : Upward

Install spacer.Clean windshield glass to install position of spacer by using white gasoline or degreasing agent. Remove release liner of double-sided tape for installing spacer. Install spacer on windshield glass as shown in the figures.

Unit: mm (in)

Edge
R-end

Install windshield molding.Clean windshield glass to install position of windshield molding by using white gasoline or degreasing agent. Apply glass primer on windshield glass as shown in the figure.

C : Glass primer applying range
D : Allowed glass primer applying range
Black print
Edge
R-end
Remove release liner of double-sided tape for installing windshield molding. Install windshield molding on windshield glass as shown in the figure.

Unit: mm (in)

*1 : ± 2.0 mm (0.08 in)
*2 : ± 1.2 mm (0.18 in)
Black print
Double-sided tape on windshield molding
Edge

Apply glass primer along the entire circumference of windshield glass. For the range of glass primer, refer to Exploded View.

Apply painted surface primer to the body side bonding surface. For the range of painted surface primer, refer to Exploded View.

Apply adhesive to windshield glass by using an adhesive gun. For the volume of adhesive, refer to Exploded View.

C : More than 60.0 mm (2.36 in)

Use suction lifter (A) that is installed in advance, align clips and roof panel holes and the matching marks of the body side outer panel and windshield glass to install them on the vehicle.

Press entire surface of windshield glass lightly to fit it completely.

Correct any adhesive overflow or shortage using a spatula to make the surface smooth.

Remove protective tape.

Install removed parts.

Reuse Windshield Glass

Use a cutter knife or scraper, and leave the adhesive on each panel and windshield glass thin and smooth as shown in the figure.

Remove remaining adhesive, spacer, windshield molding, dam sealant rubber, dam sealant rubber upper, and clips from windshield glass surface.

Clean the bonded area on windshield glass and body panel side using a white gasoline or degreasing agent.

Install clips.Clean windshield glass to install position of clip by using white gasoline or degreasing agent. Apply glass primer on windshield glass of clip install position. Remove release liner of double-sided tape for installing clip. Install clip on windshield glass along with the matching marks (A) as shown in the figure.

Unit: mm (in)

* : ± 1.0 mm (0.04 in)
Edge
R-end

Install insulator.Clean windshield glass to install position of insulator by using white gasoline or degreasing agent. Remove release liner of double-sided tape for installing insulator. Install insulator on windshield glass as shown in the figure.

Unit: mm (in)

* : ± 2.0 mm (0.08 in)
Edge
Center
Vertex
H : Dimensions
  • Top left and right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Side left and right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Lower left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Bottom left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Bottom middle left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    : Upward
  • Bottom center left

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Center
    Edge
    : Upward
  • Bottom center right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Center
    Edge
    : Upward
  • Bottom right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    Edge
    R-end
    : Upward
  • Lower right

    Unit: mm (in)

    * : ± 1.0 mm (0.04 in)
    R-end
    : Upward

Install spacer.Clean windshield glass to install position of spacer by using white gasoline or degreasing agent. Remove release liner of double-sided tape for installing spacer. Install spacer on windshield glass as shown in the figures.

Unit: mm (in)

Edge
R-end

Install windshield molding.Clean windshield glass to install position of windshield molding by using white gasoline or degreasing agent. Apply glass primer on windshield glass as shown in the figure.

C : Glass primer applying range
D : Allowed glass primer applying range
Black print
Edge
R-end
Remove release liner of double-sided tape for installing windshield molding. Install windshield molding on windshield glass as shown in the figure.

Unit: mm (in)

*1 : ± 2.0 mm (0.08 in)
*2 : ± 1.2 mm (0.18 in)
Black print
Double-sided tape on windshield molding
Edge

Apply glass primer along the entire circumference of windshield glass. For the range of glass primer, refer to Exploded View.

Apply painted surface primer to the body side bonding surface. For the range of painted surface primer, refer to Exploded View.

Apply adhesive to windshield glass by using an adhesive gun. For the volume of adhesive, refer to Exploded View.

C : More than 60.0 mm (2.36 in)

Use suction lifter (A) that is installed in advance, align clips and roof panel holes and the matching marks of the body side outer panel and windshield glass to install them on the vehicle.

Press entire surface of windshield glass lightly to fit it completely.

Correct any adhesive overflow or shortage using a spatula to make the surface smooth.

Remove protective tape.

Install removed parts.

Inspection

WATER LEAKAGE INSPECTION