Back Door Window Glass
Exploded View

| Back door outer panel | Back door window glass | Spacer A | |||
| Clip upper RH | Clip lower | Spacer B | |||
| Spacer C | Back door window glass molding | Dam sealant rubber | |||
| Clip upper LH | Glass primer | Adhesive | |||
| Adhesive mark | |||||
| : Always replace after every disassembly. | |||||
Unit: mm (in)
| Portion | Primer range | Adhesive range | |||
|---|---|---|---|---|---|
| G | H | ||||
| Back door window glass – Back door outer panel | D | From adhesive mark, more than 7.5 (0.30) | 7.0 + 2.0, - 0.0 (0.28 + 0.08, - 0.0) |
12.0 + 2.0, - 0.0 (0.47 + 0.08. - 0.0) |
|
| E | From adhesive mark, more than 7.5 (0.30) | ||||
| F | From adhesive mark, 4.8 (0.19) | ||||
Removal and Installation
REMOVAL
Replacement Back Door Window Glass
Remove back door inner finisher. Refer to Removal and Installation.
Remove back door upper garnish. Refer to Removal and Installation.
Remove back door side garnish. Refer to Removal and Installation.
Remove intelligent rear view mirror camera [rear camera (driving video recorder)]. Refer to Removal and Installation [with rear camera (driving video recorder)].
Disconnect window defogger connector
(LH and RH side).

Remove rear spoiler. Refer to Removal and Installation.
Remove rear side spoiler. Refer to Removal and Installation.
Remove back door finisher upper or tail lamp. Refer to following.
Back door finisher upper : Removal and Installation.
Tail lamp : Removal and Installation.
Remove rear wiper motor. Refer to Removal and Installation.
Apply protective tapes (A) on back door panel around back door window glass to protect painted surface from damage.

Cut the adhesive
using a windshield cutter (A) between along with back door window glass
and back door outer panel
.

Cut the adhesive using a piano wire.Pass the piano wire passenger room to bonded area of back door window glass using a wire pierce.
Tie both ends of the piano wire (B) to wire grip (A), etc.
Use suction lifter (A) to remove back door window glass from the vehicle.

Remove remaining parts from back door outer panel.
Reuse Back Door Window Glass
Remove back door inner finisher. Refer to Removal and Installation.
Remove back door upper garnish. Refer to Removal and Installation.
Remove back door side garnish. Refer to Removal and Installation.
Remove intelligent rear view mirror camera [rear camera (driving video recorder)]. Refer to Removal and Installation [with rear camera (driving video recorder)].
Disconnect window defogger connector
(LH and RH side).

Remove rear spoiler. Refer to Removal and Installation.
Remove rear side spoiler. Refer to Removal and Installation.
Remove back door finisher upper or tail lamp. Refer to following.
Back door finisher upper : Removal and Installation.
Tail lamp : Removal and Installation.
Remove rear wiper motor. Refer to Removal and Installation.
Apply protective tapes (A) on back door outer panel around back door window glass to protect painted surface from damage.

Apply matching marks (A) to back door window glass and back door outer panel.

Cut the adhesive using a piano wire.Pass the piano wire passenger room to bonded area of back door window glass using a wire pierce.
Tie both ends of the piano wire (B) to wire grip (A), etc.
Use suction lifter (A) to remove back door window glass from the vehicle.

Remove remaining parts from back door outer panel.
INSTALLATION
Replacement Back Door Window Glass
Make the remaining adhesive on back door outer panel to thin and smooth using a cutter knife or scraper as shown in the figure.

Place back door window glass on the vehicle temporarily, and then apply matching marks (A) on back door window glass and back door outer panel as shown in the figure.

Set suction lifter (A) to back door window glass
on glass stand (B).

Clean the bonded area on back door window glass and back door outer panel using a white gasoline or degreasing agent.
Install dam sealant rubber.Clean back door widow glass to install position of dam sealant rubber using white gasoline or degreasing agent. Install dam sealant rubber while removing release liner as shown in the figure.

Unit: mm (in)
| *1 | : ± 1.5 mm (0.06 in) |
| *2 | : ± 5.0 mm (0.20 in) |
| Center | |
| Edge | |
| Matching mark |
Install back door widow glass molding.Clean back door window glass to install position of back door window glass molding using white gasoline or degreasing agent. Apply glass primer on back door window glass of back door window glass molding install positions. Install back door window glass molding while removing release liner as shown in the figure.

Unit: mm (in)
| *1 | : ± 1.0 mm (0.04 in) |
| *2 | : ± 1.5 mm (0.06 in) |
| Double-sided tape | |
| Edge | |
| R-end |
Install spacer C.Clean back door window glass molding to install position of spacer C using white gasoline or degreasing agent. Apply glass primer on back door window glass molding install positions of spacer C. Remove release liner of double-sided tape, and then install spacer C as shown in the figure.

Unit: mm (in)
| *1 | : ± 3.0 mm (0.19 in) |
| *2 | : ± 1.0 mm (0.04 in) |
| Edge |
Apply glass primer along the entire circumference of back door window glass. For the range of glass primer, refer to Exploded View.
Apply adhesive to back door window glass by using an adhesive gun. For the volume of adhesive, refer to Exploded View.

| B | : More than 30 mm (1.18 in) |
Install back door window glass to vehicle by checking the matching marks on back door outer panel and back door window glass.
Press entire surface of back door window glass lightly to fit it completely.
Correct any adhesive overflow or shortage using a spatula to make the surface smooth.
Remove protective tapes.
Install the removed parts.
Reuse Back Door Window Glass
Make the remaining adhesive on back door outer panel to thin and smooth using a cutter knife or scraper as shown in the figure.

Remove remaining adhesive etc. using a cutter knife or scraper back door window glass.
Clean the bonded area on back door window glass and back door outer panel using a white gasoline or degreasing agent.
Install clips.Remove remaining clips after taking the matching marks. Clean back door window glass to install position of clips by using white gasoline or degreasing agent. Apply glass primer on back door window glass of clip install positions. Remove release liner of double-sided tape for installing clips. Install clips on back door window glass along with matching marks
as shown in the figure.

Install spacer A.Clean back door widow glass to install position of spacer A using white gasoline or degreasing agent. Remove release liner of double-sided tape, and then install spacer A as shown in the figure.

Unit: mm (in)
| * | : ± 2.0 mm (0.08 in) |
| : Install to matching marks |
|
| Edge | |
| R-end |
Install dam sealant rubber.Clean back door widow glass to install position of dam sealant rubber using white gasoline or degreasing agent. Install dam sealant rubber while removing release liner as shown in the figure.

Unit: mm (in)
| *1 | : ± 1.5 mm (0.06 in) |
| *2 | : ± 5.0 mm (0.20 in) |
| Center | |
| Edge | |
| Matching mark |
Install spacer B.Clean back door window glass to install position of spacer B using white gasoline or degreasing agent. Remove release liner of double-sided tape, and then install spacer B as shown in the figure.

Unit: mm (in)
| D | : Dimensions |
| * | : ± 2.0 mm (0.08 in) |
| Edge | |
| R-end |

Unit: mm (in)
| *1 | : ± 1.0 mm (0.04 in) |
| *2 | : ± 1.5 mm (0.06 in) |
| Double-sided tape | |
| Edge | |
| R-end |
Install spacer C.Clean back door window glass molding to install position of spacer C using white gasoline or degreasing agent. Apply glass primer on back door window glass molding to install position of spacer C. Remove release liner of double-sided tape, and then install spacer C as shown in the figure.

Unit: mm (in)
| *1 | : ± 3.0 mm (0.19 in) |
| *2 | : ± 1.0 mm (0.04 in) |
| Edge |
Apply glass primer along the entire circumference of back door window glass. For the range of glass primer, refer to Exploded View.
Apply adhesive to back door window glass by using an adhesive gun. For the volume of adhesive, refer to Exploded View.

| B | : More than 30 mm (1.18 in) |
Install back door window glass to vehicle by checking the matching marks on back door outer panel and back door window glass.
Press entire surface of back door window glass lightly to fit it completely.
Correct any adhesive overflow or shortage using a spatula to make the surface smooth.
Remove protective tapes.
Install the removed parts.