Interior

Body side trim

In this manual: Interior
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Exploded View

1. Rear body side welt

1. Rear body side welt 2. Center pillar upper garnish 3. Front body side welt
4. Front pillar garnish 5. Metal clip
6. Dash side finisher
7. Harness clip
8. Front kicking plate inner 9. Center pillar lower garnish 10. Rear kicking plate inner

: Pawl: Clip
: Metal clip: Pawl
: Vehicle front: Metal clip
: Do not reuse: Vehicle front
Front pillar garnish : Removal and Installation: Do not reuse


Front pillar garnish : Removal and Installation

REMOVAL

CAUTION:
• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Release front pillar garnish portion of front body side welt.

2. Remove front pillar garnish.

1. Disengage front pillar garnish fixing clips with a remover tool (A).

2. Twist clip portion of front pillar garnish using long nose pliers: Clip


2. Twist clip portion of front pillar garnish using long nose pliers while pulling upper side of front pillar garnish toward inside, and then remove clip from front pillar garnish side.

3. Remove front pillar garnish of pull toward the arrow direction.

INSTALLATION

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• When installing front pillar garnish, check that clips are securely in body panel holes, and press them in.

• Replace front pillar garnish with a new part after removal. Never reuse front pillar garnish.

Kicking plate inner : Removal and Installation

REMOVAL

CAUTION:
Never damage the body.

FRONT KICKING PLATE INNER

Pull up front kicking plate inner, and then disengage the pawls.

: Pawl


REAR KICKING PLATE INNER

REAR KICKING PLATE INNER

Pull up rear kicking plate inner, and then disengage the pawls.

: Pawl


INSATALLATION

INSATALLATION

Install in the reverse order of removal.

Dash side finisher : Removal and Installation

REMOVAL

CAUTION:
Never damage the body.
1. Remove front kicking plate inner. Refer to INT-19, "KICKING PLATE INNER : Removal and Installation".

2. Pull back dash side finisher, and then disengage the pawls.

: Pawl


3. Disconnect dash side finisher, vehicle front side, from stud bolt and

3. Disconnect dash side finisher, vehicle front side, from stud bolt and remove dash side finisher.

INSTALLATION

Install in the reverse order of removal.

Body side welt : Removal and Instal

REMOVAL

CAUTION:
• Never excessively pull body side welt.

• Never damage the body.

FRONT BODY SIDE WELT

1. Remove front kicking plate inner. Refer to INT-19, "KICKING PLATE INNER : Removal and Installation".

2. Remove front body side welt.

REAR BODY SIDE WELT

1. Remove rear kicking plate inner. Refer to INT-19, "KICKING PLATE INNER : Removal and Installation".

2. Remove rear body side welt.

INSTALLATION

Install in the reverse order of removal.

Center pillar lower garnish : Removal and Installation

REMOVAL

CAUTION:
• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Fully open front door and rear door. 2. Slide front seat to the fully forward position. Tilt seatback forward. 3. Remove Front body side welt and rear body side welt. Refer to INT-20, "BODY SIDE WELT : Removal and Installation".

4. Disengage center pillar lower garnish fixing clips and pawls with a remover tool (A), and then remove center pillar lower garnish.

: Pawl: Clip
: Pawl


INSTALLATION

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
When installing center pillar lower garnish, check that clips are securely in body panel holes, and press them in.

Center pillar upper garnish : Removal and Installation

REMOVAL

CAUTION:
• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Remove center pillar lower garnish. Refer to INT-20, "CENTER PILLAR LOWER GARNISH : Removal and Installation". 2. Remove front seat belt shoulder anchor. Refer toSB-5, "SEAT BELT RETRACTOR : Removal and Installation".

3. Disengage center pillar upper garnish lower side fixing pawl.

: Pawl


4. Disengage center pillar upper garnish upper side fixing clip.

4. Disengage center pillar upper garnish upper side fixing clip.

NOTE

:
Removal operation can be performed easily when pressing pawl by inserting a removal tool from direction (A) as shown in the figure.

CAUTION:

CAUTION:
Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise, pawl may be damaged and fragments may drop in panel holes on body.

Note the following items, and install in the reverse order of removal.

CAUTION:
• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper garnish.

• When installing center pillar upper garnish, check that pawls are securely in body panel holes, and press them in.