Engine Mechanical MR16DDT

Camshaft

In this manual: Engine Mechanical MR16DDT
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~11min read
0102030405021N·mlb·ft
Tightening torque found on this page

Exploded View

1. Camshaft position sensor (PHASE)

1. Camshaft position sensor (PHASE) 2. O-ring
3. Camshaft bracket
4. Camshaft (EXH)
5. Camshaft sprocket (EXH) 6. Camshaft sprocket (INT) 7. Camshaft (INT)
8. Valve lifter (EXH)
9. Valve lifter (INT)
10. Signal plate (INT)
11 Signal plate (EXH)

A.Tightening must be done following the installation procedure.

Refer to EM-79

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly. : Sealing point: Should be lubricated with oil.


: Select with proper thickness.: Sealing point
Removal and Installation: Select with proper thickness.


Removal and Installation

CAUTION:
The rotating direction in the text indicates all directions seen from the engine front.

REMOVAL

1. Remove the following parts. • Intake manifold: Refer to EM-28, "Exploded View". • Rocker cover: Refer to EM-23, "Exploded View".

• Front cover and timing chain related parts: Refer to EM-67, "Exploded View".

NOTE

:
Removal of oil pump drive related part is not necessary.

2. Remove camshaft position sensor (PHASE) from camshaft bracket.

CAUTION:
• Handle camshaft position sensor (PHASE) carefully and avoid impacts. • Never disassemble camshaft position sensor (PHASE).

• Never place sensor where it is exposed to magnetism.

3. Put the matching mark (A) on the camshaft sprocket (INT) (1), camshaft sprocket (EXH) (2) and the camshaft bracket (1) as shown in the figure.

NOTE

:
It prevents the knock pin of the camshaft (INT) from engaging with the incorrect pin hole when installing the camshaft sprocket (INT).

4. Remove camshaft sprockets (INT and EXH).

4. Remove camshaft sprockets (INT and EXH).

• Secure hexagonal part (A) of camshaft with a wrench. Loosen camshaft sprocket mounting bolts and remove camshaft sprocket.

1 : Camshaft sprocket (INT) 2 : Camshaft sprocket (EXH)

CAUTION:
• Never rotate crankshaft or camshaft while timing chain is removed. It causes interference between valve and piston.

• Never loosen the mounting bolts with securing anything other than the camshaft hexagonal part or with tensioning the timing chain.

5. Remove camshaft bracket with the following procedure:

5. Remove camshaft bracket with the following procedure: a. Loosen mounting bolts in reverse order as shown in the figur

: Engine front


b. Cut liquid gasket by prying the position (

b. Cut liquid gasket by prying the position () shown in the figure,
) shown in the figure, and then remove the camshaft bracket.

CAUTION:: Engine front


CAUTION:
• Be careful not to damage the mating surface.

• A more adhesive liquid gasket is applied compared to previous types when shipped, so it should not be forced off the position not specified.

6. Remove camshafts.

6. Remove camshafts. 7. Remove valve lifters. • Identify installation positions, and store them without mixing them up.

8. Remove signal plate from camshaft, if necessary.

INSTALLATION

1. Install valve lifters.

• Install them in the original positions.

2. Install camshafts. • Clean camshaft journal to remove any foreign material.

• Distinguish between the intake and the exhaust by looking at the different shapes of the front and rear ends of the camshaft or using the identification colors (A) and (B).

1 : Camshaft (EXH)
2 : Camshaft (INT)

• Install camshafts so that camshaft dowel pins (A) on the front

• Install camshafts so that camshaft dowel pins (A) on the front side are positioned as shown in the figure.

1 : Camshaft (EXH)

1 : Camshaft (EXH)
2 : Camshaft (INT)

NOTE

: Though camshaft does not stop at the positions as shown in the figure, for the placement of cam nose, it is generally accepted camshaft is placed for the same direction of the figure.

3. Install camshaft bracket with the following procedure:

3. Install camshaft bracket with the following procedure: a. Remove foreign material completely from camshaft bracket backside and from cylinder head installation face.

b. Apply liquid gasket (A) to camshaft bracket as shown in the figure.

b : Plug hole inner wall c : 3.4 - 4.4mm (0.134 - 0.173 in) : Engine outside: Engine front
Use Genuine Liquid Gasket or equivalent.: Engine outside


Use Genuine Liquid Gasket or equivalent.
c. Tighten mounting bolts of camshaft brackets in the following

c. Tighten mounting bolts of camshaft brackets in the following steps, in numerical order as shown in the figure.

• There are two types of mounting bolts. Refer to the following: Engine front


• There are two types of mounting bolts. Refer to the following for locating bolts.

M6 bolts [thread length: 57.5 mm (2.264 in)] : 13, 14, and 15 in the figure M6 bolts [thread length: 35.0 mm (1.378 in)] : Except the above

i. Tighten mounting bolts in numerical order.

i. Tighten mounting bolts in numerical order.

ii. Tighten mounting bolts in numerical order.: 2 N·m


ii. Tighten mounting bolts in numerical order.

iii. Tighten mounting bolts in numerical order.: 5,9 N·m


iii. Tighten mounting bolts in numerical order.

CAUTION:: 9,5 N·m


CAUTION:
After tightening mounting bolts of camshaft brackets, be sure to wipe off excessive liquid gasket from the mating surface of cylinder head.

4. Install the camshaft sprocket (INT) to the camshaft (INT) with the following procedure.

a. When the camshaft sprocket (INT) (2) and camshaft sprocket (EXH) (3) is removed, refer to the paint mark (A) put according to step “3”. Securely align the knock pin and the pin hole, and then install them.

1 : Camshaft bracket

b. Tighten bolts in the following steps.

b. Tighten bolts in the following steps.

• Secure the hexagonal part of camshaft (INT) using wrench to tighten mounting bolt.

i. Tighten camshaft (INT) mounting bolt.

ii. Turn 67 degrees clockwise (angle tightening).: 35 N·m


ii. Turn 67 degrees clockwise (angle tightening).

CAUTION:
Check the tightening angle by using an angle wrench [SST: KV10112100 (BT8653-A)] (B) or protractor. Never judge by visual inspection without an angle wrench.

1 : Camshaft sprocket (INT) A : Camshaft (INT) hexagonal part

5. Install timing chain and related parts. Refer to EM-67, "Exploded View".

5. Install timing chain and related parts. Refer to EM-67, "Exploded View".

6. Inspect and adjust valve clearance. Refer to EM-14, "Inspection and Adjustment".

7. Install remaining parts in the reverse order of removal.

Inspection

INSPECTION AFTER REMOVAL

Camshaft Runout
1. Put V-block on a precise flat table, and support No. 2 and 5 journal of camshaft.

CAUTION:
Never support No. 1 journal (on the side of camshaft sprocket) because it has a different diameter from the other four locations. 2. Set dial indicator (A) vertically to No. 3 journal.

3. Turn camshaft to one direction with hands, and measure the camshaft runout on dial indicator. (Total indicator reading)

Standard and Limit : Refer to EM-130, "Camshaft".

4. If it exceeds the limit, replace camshaft.

Camshaft Cam Height

Camshaft Cam Height

1. Measure the camshaft cam height with a micrometer (A).

Standard and Limit : Refer to EM-130, "Camshaft".

2. If it exceeds the limit, replace camshaft.

2. If it exceeds the limit, replace camshaft.

Camshaft Journal Oil Clearance CAMSHAFT JOURNAL OUTER DIAMETER Measure the outer diameter of camshaft journal with a micrometer (A).

Standard : Refer to EM-130, "Camshaft".

CAMSHAFT BRACKET INNER DIAMETER

CAMSHAFT BRACKET INNER DIAMETER

• Tighten camshaft bracket bolts with specified torque. Refer to EM-79, "Removal and Installation".

• Measure the inner diameter of camshaft bracket with a bore gauge (A).

B : Measuring direction of inner diameter

Standard : Refer to EM-130, "Camshaft".

CAMSHAFT JOURNAL OIL CLEARANCE

CAMSHAFT JOURNAL OIL CLEARANCE

• (Oil clearance) = (Camshaft bracket inner diameter) – (Camshaft journal diameter)

Standard and Limit : Refer to EM-130, "Camshaft".

• If it exceeds the limit, replace camshaft or cylinder head, or both.

NOTE

:
Camshaft bracket cannot be replaced as a single part, because it is machined together with cylinder head.

Replace whole cylinder head assembly.

Camshaft End Play
1. Install camshaft in cylinder head. Refer to EM-79, "Removal and Installation".

2. Install dial indicator in thrust direction on front end of camshaft.

Read the end play of dial indicator (A) when camshaft is moved forward/backward (in direction to axis).

Standard and Limit : Refer to EM-130, "Camshaft".

• Measure the following parts if out of the standard.

• Measure the following parts if out of the standard.

- Dimension (A) for groove of cylinder head No. 1 journal

Standard : 4.000 - 4.030 mm (0.1575 - 0.1587 in)

- Dimension (B) for camshaft flange

Standard : 3.877 - 3.925 mm (0.1526 - 0.1545 in)

• Refer to the standards above, and then replace camshaft and/ or cylinder head.

Camshaft Sprocket Runout

Camshaft Sprocket Runout 1. Put V-block on precise flat table, and support No. 2 and 5 journals of camshaft.

CAUTION:
Never support No. 1 journal (on the side of camshaft sprocket) because it has a different diameter from the other four locations.

2. Measure the camshaft sprocket runout with a dial indicator (A).

(Total indicator reading)

Limit : Refer to EM-130, "Camshaft".

• If it exceeds the limit, replace camshaft sprocket.

Valve Lifter

Valve Lifter
Check if surface of valve lifter has any wear or cracks.

• If anything above is found, replace valve lifter. Refer to EM-130, "Camshaft".

Valve Lifter Clearance

Valve Lifter Clearance

VALVE LIFTER OUTER DIAMETER

• Measure the outer diameter of valve lifter with a micrometer (A).

Standard : Refer to EM-130, "Camshaft".

VALVE LIFTER HOLE DIAMETER

VALVE LIFTER HOLE DIAMETER

Measure the inner diameter of valve lifter hole of cylinder head with an inside micrometer (A).

Standard : Refer to EM-130, "Camshaft".

VALVE LIFTER CLEARANCE

• (Valve lifter clearance) = (Valve lifter hole diameter) – (Valve lifter outer diameter)

Standard : Refer to EM-130, "Camshaft".

• If out of the standard, referring to the each standard of valve lifter outer diameter and valve lifter hole diameter, replace either or both valve lifter and cylinder head.

INSPECTION AFTER INSTALLATION

INSPECTION AFTER INSTALLATION

Inspection of Camshaft Sprocket (INT) Oil Groove

CAUTION:
• Perform this inspection only when DTC P0011 is detected in self-diagnostic results of CONSULT-III and it is directed according to inspection procedure of EC section. Refer to EC-163, "Diagnosis Procedure".

• Check when engine is cold so as to prevent burns by the splashing engine oil.

1. Check engine oil level. Refer to LU-8, "Inspection".

2. Perform the following procedure so as to prevent the engine from being unintentionally started while checking.

a. Release the fuel pressure. Refer to EC-140, "Work Procedure". b. Remove intake manifold. Refer to EM-28, "Exploded View". c. Disconnect ignition coil and injector harness connectors.

d. Support the bottom surface of engine using a transmission jack, and then remove the engine mounting bracket (RH) and engine mounting insulator (RH). Refer to EM-55, "2WD : Exploded View".

3. Remove intake valve timing control solenoid valve. Refer to EM-67, "Exploded View".

• Lift the front side of the engine with a jack base to remove intake valve timing control solenoid valve.

4. Clean the mounting area of intake valve timing control solenoid valve, and then insert a clean waste with no oil adhesion into the oil hole of the cylinder head. 5. Install engine mounting insulator (RH) and engine mounting bracket (RH). (After the removal of intake valve timing control solenoid valve and insertion of a waste into the oil hole.)
6. Perform cranking to check that engine oil comes out from the oil hole (mounting hole of intake valve timing control solenoid valve) of cylinder head.

• Regarding the engine oil check, judge it by the amount of oil adhered to the wasted inserted into the oil hole.

WARNING:
• Never insert fingers into the oil hole.

• Be careful not to touch rotating parts (drive belt, idler pulleys and crankshaft pulley, etc.).

CAUTION:
• Never perform cranking without installing the engine mounting insulator (RH) and engine mounting bracket (RH). • Prevent splashing by using a shop cloth so as to prevent the worker from injury from engine oil and so as to prevent engine oil contamination.

• Prevent splashing by using a shop cloth so as to prevent engine oil from being splashed to engine and vehicle. Especially, be careful not to apply engine oil to rubber parts of drive belt, engine mounting insulator, etc. Wipe engine oil off immediately if it is splashed.

7. Perform the following inspection if engine oil does not come out from intake valve timing control solenoid valve oil hole of the cylinder head. • Remove oil filter (for intake valve timing control), and then clean it. Refer to EM-103, "Exploded View".

• Clean oil groove between oil strainer and intake valve timing control solenoid valve. Refer to LU-3, "Engine Lubrication System" and LU-3, "Engine Lubrication System Schematic".

8. Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT), and then check each oil groove for clogging.

• Clean oil groove if necessary. Refer to LU-3, "Engine Lubrication System" and LU-3, "Engine Lubrication System Schematic".

9. After inspection, install removed parts in the reverse order.