Engine Mechanical MR16DDT

Timing chain

In this manual: Engine Mechanical MR16DDT
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~11min read
0102030405029.422N·mlb·ft
Tightening torque found on this page

Exploded View

1. Timing chain slack guide

1. Timing chain slack guide 2. Timing chain tensioner 3. Timing chain
4. Oil pump drive chain 5. Crankshaft sprocket
6. Crankshaft key
7. Oil pump sprocket
8. Front cover
9. O-ring
10. O-ring
11. Oil control valve cover 12. O-ring
13. Oil control valve (EXH) 14. Oil control valve (INT) 15. Crankshaft pulley bolt 16. Crankshaft pulley
17. Front oil seal
18. Oil pump drive chain tensioner 19. O-ring
20. Timing chain tension guide 21. Camshaft spsocket (INT) 22. Camshaft sprocket (EXH) 23. O-ring

A.Tightening must be done following the installation procedure.

Refer to EM-68

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly. : Sealing point: Should be lubricated with oil.


Removal and Installation: Sealing point


Removal and Installation

REMOVAL

CAUTION:
The rotating direction in the text indicates all directions seen from the engine front.

1. Drain engine oil. Refer to LU-9, "Draining".

CAUTION:
Perform this step when engine is cold.
2. Remove the following parts: • Intake manifold: Refer to EM-28, "Exploded View".

• Rocker cover: Refer to EM-23, "Exploded View".

3. Set No. 1 cylinder at TDC on its compression stroke with the following procedure:
a. Rotate crankshaft pulley (1) clockwise and align TDC mark (no paint) (B) to timing indicator (A) on front cover.

C : White paint mark (Not use for service)

b. At the same time, check that the cam noses of the No. 1 cylinder

b. At the same time, check that the cam noses of the No. 1 cylinder are located ( figure.) as shown in the
figure.

1 : Camshaft (INT)
2 : Camshaft (EXH)
• If not, rotate crankshaft pulley one revolution (360 degrees): Engine front


• If not, rotate crankshaft pulley one revolution (360 degrees) and align as shown in the figure.

4. Remove crankshaft pulley with the following procedure:

4. Remove crankshaft pulley with the following procedure:

a. Fix crankshaft pulley (1) with a pulley holder (commercial service tool) (A), loosen crankshaft pulley bolt, and locate bolt seating surface at 10 mm (0.39 in) from its original position.

CAUTION:
Never remove the crankshaft pulley bolt as they will be used as a supporting point for the pulley puller [SST: KV11103000 ( — )].
b. Attach a pulley puller [SST: KV11103000 ( — )] (A) in the M6

b. Attach a pulley puller [SST: KV11103000 ( — )] (A) in the M6 thread hole on crankshaft pulley (1), and remove crankshaft pulley.

5. Remove oil pan (lower). Refer to EM-99, "Exploded View".

5. Remove oil pan (lower). Refer to EM-99, "Exploded View".

NOTE

:
If crankshaft sprocket and oil pump drive component are not removed, this step is unnecessary.

6. Remove intake valve timing control solenoid valve. 7. Remove drive belt auto-tensioner. Refer to EM-66, "Exploded View".

8. Remove front cover with the following procedure: a. Loosen mounting bolts in reverse order as shown in the figure.

b. Cut liquid gasket by prying the position (

b. Cut liquid gasket by prying the position () shown in the figure,
) shown in the figure, and then remove the front cover.

CAUTION:
• Be careful not to damage the mating surface.

• A more adhesive liquid gasket is applied compared to previous types when shipped, so it should not be forced off the position not specified.

9. Remove front oil seal from front cover.

9. Remove front oil seal from front cover.

CAUTION:
Be careful not to damage front cover.

• Lift up front oil seal using a screwdriver.

10. Remove timing chain tensioner with the following procedure: a. Insert a wire (A) (e.g. clip) into the top groove with the timing chain tensioner plunger pressed.

NOTE:
Timing chain tensioner plunger is securely fixed by inserting a wire (e.g. clip).

b. Remove timing chain tensioner (1).

11. Remove slack guide (2), tension guide (3) and timing chain (1).

11. Remove slack guide (2), tension guide (3) and timing chain (1).

CAUTION:
Never rotate each crankshaft and camshaft individually while timing chain is removed. It causes interference between valve and piston.
NOTE:

If timing chain is difficult to remove, remove camshaft sprocket (EXH) first to remove timing chain.

12. Remove crankshaft sprocket and oil pump drive component with the

12. Remove crankshaft sprocket and oil pump drive component with the following procedure: a. Push oil pump drive chain tensioner (1) in the direction show in the figure (A). b. Insert a stopper pin (A) into the body hole (B). c. Remove oil pump chain tensioner.

• When the holes on lever and tensioner body cannot be alirned, align these holes by slightly moving the oil pump chain tensioner slack guide.

d. Hold the WAF part of oil pump shaft [WAF: 10 mm (0.39 in)] (A),

d. Hold the WAF part of oil pump shaft [WAF: 10 mm (0.39 in)] (A), and then loosen the oil pump sprocket bolt and remove it.

1 : Oil pan (upper)
CAUTION:: Engine front


CAUTION:
• Secure the oil pump shaft with the WAF part.

• Never loosen the oil pump sprocket bolt by tightening the oil pump drive chain.

13. Remove tension guide (front cover side) from front cover, if necessary.

13. Remove tension guide (front cover side) from front cover, if necessary.

INSTALLATION

NOTE

:
The figure shows the relationship between the matching mark on each timing chain and that on the corresponding sprocket, with the components installed.

1 : Timing chain
2 : Camshaft sprocket (EXH) 3 : Slack guide
4 : Timing chain tensioner 5 : Crankshaft sprocket
6 : Oil pump drive chain 7 : Oil pump sprocket
8 : Oil pump drive chain tensioner 9 : Tension guide
10 : Camshaft sprocket (INT)

A : Matching mark (dark blue link) B : Matching mark (outer groove*) C : Crankshaft key position (straight up) D : Matching mark (stamping) E : Matching mark (white link) F : Matching mark (yellow link) G : Matching mark (outer groove)

*: There are two outer grooves in camshaft sprocket (EXH). The wider one is a matching mark.

1. Check that crankshaft key points straight up.

1. Check that crankshaft key points straight up.

2. If the tension guide (front cover side) is removed, install it to the front cover.

CAUTION:
Check the joint condition by sound or feeling.

3. Install crankshaft sprocket (2), oil pump sprocket (3), and oil pump drive chain (1).

A : Matching mark (stamping) B : Matching mark (yellow link) C : Matching mark (dark blue link)

• Install it by aligning matching marks on each sprockets and oil pump drive chain.

• If these matching marks are not aligned, rotate the oil pump shaft slightly to correct the position.

CAUTION:
Check matching mark position of each sprockets after installing the oil pump drive chain.
4. Hold the WAF part of oil pump shaft [WAF: 10 mm (0.39 in)] (A),

4. Hold the WAF part of oil pump shaft [WAF: 10 mm (0.39 in)] (A), and then tighten the oil pump shaft sprocket bolt.

1 : Oil pan (upper)
CAUTION:: Engine front


CAUTION:
• Secure the oil pump shaft with the WAF part.

• Never loosen the oil pump shaft sprocket bolt by tightening the oil pump drive chain.

5. Install oil pump chain tensioner (1).

5. Install oil pump chain tensioner (1). • Fix the plunger at the most compressed position using a stopper pin (A), and then install it. • Securely pull out (pin after installing the oil ) the stopper
pin after installing the oil pump chain tensioner.

• Check matching mark position of oil pump drive chain and each sprockets again.

6. Align the matching marks of each sprockets with the matching

6. Align the matching marks of each sprockets with the matching marks of timing chain.

1 : Camshaft sprocket (EXH) 2 : Camshaft sprocket (INT) 3 : Timing chain

A : Matching mark (dark blue link) B : Matching mark (outer groove*) C : Matching mark (outer groove) D : Matching mark (white link) E : Matching mark (stamping)

*: There are 2 outer grooves in camshaft sprocket (EXH). The wider one is a matching mark.

• If these matching marks are not aligned, rotate the camshaft slightly by holding the hexagonal portion to correct the position.

CAUTION:
Check matching mark position of each sprocket and timing chain again after installing the timing chain.
7. Install the slack guide (2) and the tension guide (3).

7. Install the slack guide (2) and the tension guide (3).

1 : Timing chain

8. Install timing chain tensioner.

8. Install timing chain tensioner.

• Fix the plunger at the most compressed position using a stopper pin, and then install it.

• Securely pull out the stopper pin after installing the timing chain tensioner.

9. Check matching mark position of timing chain and each sprockets again. 10. Install front oil seal. Refer to EM-88, "FRONT OIL SEAL : Removal and Installation".

11. Install front cover with the following procedure: a. Install new O-ring to cylinder block.

CAUTION:
Never misalign O-ring.

b. Apply a continuous bead of liquid gasket (D) with a tube presser (commercial service tool) to front cover as shown in the figure.

1 : Cylinder head
2 : Front cover
A : Liquid gasket application area b : 4.0 - 5.6 mm (0.157 - 0.220 in) c : φ3.4 - 4.4 mm (0.134 - 0.173 in) Use Genuine Liquid Gasket or equivalent.: Engine outside


Use Genuine Liquid Gasket or equivalent.
c. Check that matching marks of timing chain and each sprockets are still

c. Check that matching marks of timing chain and each sprockets are still aligned. Then install front cover.

CAUTION:
• Check O-ring on cylinder block is correctly installed.

• Be careful not to damage front oil seal by interference with front end of crankshaft.

d. Install front cover, and tighten mounting bolts in numerical order as shown in the figure.

• Refer to the following for the installation position of bolts.

M6 bolt : No. 1
M10 bolts : No. 6, 7, 10, 13, 21 M12 bolts : No. 2, 4, 8, 11 M8 bolts : Except the above

CAUTION:
Attaching should be done within 5 minutes after liquid gasket application.

e. After all bolts are tightened, retighten them to specified torque in numerical order as shown in the figure.

CAUTION:
Be sure to wipe off any excessive liquid gasket leaking.
12. Install crankshaft pulley with the following procedure:

12. Install crankshaft pulley with the following procedure: a. When inserting crankshaft pulley with a plastic hammer, tap on its center portion (not circumference).

CAUTION:
Never damage front oil seal lip section.
b. Secure crankshaft pulley (1) with a pulley holder (commercial service tool) (A). c. Apply new engine oil to thread and seat surfaces of crankshaft pulley bolt.

d. Tighten crankshaft pulley bolt.

: 29 N·m


e. Put a paint mark (B) on crankshaft pulley (2), matching with any

e. Put a paint mark (B) on crankshaft pulley (2), matching with any one of six easy to recognize angle marks (A) on crankshaft pulley bolt (1) flange. f. Turn another 60 degrees clockwise (angle tightening). • Check the tightening angle with movement of one angle mark.

g. Check that crankshaft rotates clockwise smoothly.

13. Install remaining parts in the reverse order of removal.

13. Install remaining parts in the reverse order of removal.

Inspection

INSPECTION AFTER REMOVAL

Timing Chain
Check for cracks (A) and any excessive wear (B) at link plates and roller links of timing chain. Replace timing chain if necessary.

INSPECTION AFTER INSTALLATION

INSPECTION AFTER INSTALLATION

Inspection for Leakage The following are procedures for checking fluids leakage, lubricates leakage, and exhaust gases leakage.

• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required quantity, fill to the specified level. Refer to MA-13, "Fluids and Lubricants". • Use procedure below to check for fuel leakage. - Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leakage at connection points. - Start engine. With engine speed increased, check again for fuel leakage at connection points.

• Run engine to check for unusual noise and vibration.

NOTE

:
If hydraulic pressure inside chain tensioner drops after removal/installation, slack in guide may generate a pounding noise during and just after the engine start. However, this does not indicate an unusualness. Noise will stop after hydraulic pressure rises.

• Warm up engine thoroughly to check there is no leakage of fuel, or any oil/fluids including engine oil and engine coolant. • Bleed air from lines and hoses of applicable lines, such as in cooling system.

• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the specified level, if necessary.

*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.

*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.