Engine Mechanical MR16DDT

Unit removal and installation

In this manual: Engine Mechanical MR16DDT
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~12min read
0102030405032.924N·mlb·ft
Tightening torque found on this page
Engine assembly 2WD 2WD : Exploded View
1. Washer

1. Washer
2. Upper torque rod (RH) 3. Engine mounting insulator (RH) 4. Rear torque rod bracket 5. Rear torque rod
6. Engine mounting insulator (LH) 7. Engine mounting frame support (LH) 8. Engine mounting bracket (LH)

: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly.

CAUTION:
Check that the stud bolt (*2) is tight at the specified torque before tightening the mounting nut (*1) shown in the figure. [Stud bolt (*2) may be loosened after loosening the mounting nut (*1)]
2WD : Removal and Installation WARNING:
• Situate the vehicle on a flat and solid surface. • Place chocks at front and back of rear wheels.

• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.

CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations. • Never start working until exhaust system and coolant are cool enough. • If items or work required are not covered by the engine section, refer to the applicable sections. • Always use the support point specified for lifting. • Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoidable reasons, support at the rear axle jacking point with a transmission jack or similar tool before starting work, in preparation for the backward shift of center of gravity.

• For supporting points for lifting and jacking point at rear axle, refer to GI-36, "Garage Jack and Safety Stand and 2-Pole Lift".

REMOVAL

Outline
Remove the engine and the transaxle assembly from the vehicle downward. Separate the engine and the transaxle.

Preparation
1. Release fuel pressure. Refer to EC-140, "Work Procedure".

2. Drain engine coolant from radiator. Refer to CO-11, "Draining".

CAUTION:
• Perform this step when the engine is cold.

• Never spill engine coolant on drive belts.

3. Remove the following parts. • Engine undercover
• Front road wheels and tires • Front fender protector (RH and LH): Refer to EXT-22, "Exploded View". • Drive belt: Refer to EM-20, "Removal and Installation". • Engine cover: Refer to EM-25, "Exploded View". • Battery and battery tray: Refer to PG-124, "Exploded View". • Air duct, and air cleaner case assembly and air cleaner body assembly: Refer to EM-26, "Exploded View". • Radiator hose (upper and lower): Refer to CO-17, "Exploded View". • Exhaust front tube: Refer to EX-5, "Exploded View". • Radiator cooling fan assembly: Refer to CO-20, "Exploded View". • Charger air cooler: Refer to EM-31, "Exploded View".

• Alternator: Refer to CHG-30, "MR16DDT : Exploded View".

Engine Room LH
1. Disconnect all connections of engine harness around the battery, and then temporarily secure the engine harness into the engine side.

CAUTION:
Protect connectors using a resin bag against foreign materials during the operation.
2. Disconnect fuel feed hose quick connector. Refer to EM-43, "Exploded View". 3. Disconnect heater hoses. Refer to CO-26, "Exploded View". 4. Disconnect control linkage from transaxle. Refer to TM-78, "Exploded View". 5. Remove EVAP hoses. Refer to EM-28, "Exploded View".

6. Disconnect clutch tube on transaxle side from clutch damper. Refer to CL-24, "Exploded View".

Engine Room RH
1. Disconnect vacuum hose from intake manifold. Refer to EM-28, "Exploded View". 2. Remove A/C compressor. Refer to HA-86, "Exploded View".

3. Remove ground cable at engine side.

Vehicle Underbody
1. Remove ground cable at transaxle side. 2. Remove drive shafts (RH and LH). Refer to FAX-21, "Exploded View". 3. Remove rear torque rod. 4. Remove stabilizer connecting rod. Refer to FSU-16, "Exploded View". 5. Remove front suspension member. Refer to FSU-18, "Exploded View".

6. Preparation for the separation work of transaxle is as follows:

• Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to EM-99, "Exploded View".

Removal
1. Use a manual lift table caddy (commercial service tool) (A) or equivalently rigid tool such as a transmission jack. Securely support bottom of the engine and the transaxle assembly.

CAUTION:
Put a piece of wood or an equivalent as the supporting surface, secure a completely stable condition.
2. Remove upper torque rod (1), and engine mounting insulator

2. Remove upper torque rod (1), and engine mounting insulator (RH) (2).

: Vehicle front


3. Remove engine mounting bracket (LH) through bolt-securing

3. Remove engine mounting bracket (LH) through bolt-securing nut (B).

1 : Engine mounting insulator (LH) 2 : Engine mounting bracket support (LH) A : Through not
: Vehicle front


4. Carefully lower jack, or raise lift to remove the engine and the transaxle

4. Carefully lower jack, or raise lift to remove the engine and the transaxle assembly. When performing work, observe the following caution.

CAUTION:
• Check that no part interferes with the vehicle side. • Before and during this lifting, always check if any harnesses are left connected. • During the removal, always be careful to prevent the vehicle from falling off the lift due to changes in the center of gravity.

• If necessary, support the vehicle by setting jack or suitable tool at the rear.

Separation

1. Install engine slinger to front cover front left side (A) and cylinder head rear right side (B).

Slinger bolts: Engine front


Slinger bolts
Front cover front left side: ft-lb): 33 N·m (3.4 kg-m, 24
ft-lb)
Cylinder head rear right side: ft-lb): 25 N·m (2.6 kg-m, 18
ft-lb)

2. Remove starter motor. Refer to STR-27, "MR16DDT : Exploded View".

2. Remove starter motor. Refer to STR-27, "MR16DDT : Exploded View".

3. Lift with a hoist and separate the engine from the transaxle assembly. Refer to TM-84, "MR16DDT : Exploded View".

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
• Never allow engine oil to get on engine mounting insulator. Be careful not to damage engine mounting insulator.

• Check that each mounting insulator is seated properly, and tighten mounting nuts and bolts.

• When installation directions are specified, install parts according to the direction marks on them referring to the figure of components. Refer to EM-55, "2WD : Exploded View".

Rear torque rod bracket 1. Temporarily tighten mounting bolts in the numerical order as shown in the figure.

2. Tighten mounting bolts to the specified torque in the numerical: Engine front


2. Tighten mounting bolts to the specified torque in the numerical order as shown in the figure.

2WD : Inspection

2WD : Inspection

INSPECTION AFTER INSTALLATION

Inspection for Leakage The following are procedures for checking fluids leakage, lubricates leakage, and exhaust gases leakage.

• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required quantity, fill to the specified level. Refer to MA-13, "Fluids and Lubricants". • Use procedure below to check for fuel leakage. - Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leakage at connection points. - Start engine. With engine speed increased, check again for fuel leakage at connection points. • Run engine to check for unusual noise and vibration. • Warm up engine thoroughly to check there is no leakage of fuel, exhaust gases, or any oil/fluids including engine oil and engine coolant. • Bleed air from lines and hoses of applicable lines, such as in cooling system.

• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the specified level, if necessary.


*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.

*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.

4WD 4WD : Exploded View
1. Washer

1. Washer
2. Upper torque rod (RH) 3. Engine mounting insulator (RH) 4. Rear engine mounting bracket 5. Rear torque rod
6. Engine mounting insulator (LH)

: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly.

4WD : Removal and Installation WARNING:
• Situate the vehicle on a flat and solid surface. • Place chocks at front and back of rear wheels.

• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.

CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations. • Never start working until exhaust system and coolant are cool enough. • If items or work required are not covered by the engine section, refer to the applicable sections. • Always use the support point specified for lifting. • Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoidable reasons, support at the rear axle jacking point with a transmission jack or similar tool before starting work, in preparation for the backward shift of center of gravity.

• For supporting points for lifting and jacking point at rear axle, refer to GI-36, "Garage Jack and Safety Stand and 2-Pole Lift".

REMOVAL

Outline
Remove the engine and the transaxle assembly from the vehicle downward. Separate the engine and the transaxle.

Preparation
1. Release fuel pressure. Refer to EC-140, "Work Procedure".

2. Drain engine coolant from radiator. Refer to CO-11, "Draining".

CAUTION:
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belts. 3. Remove the following parts. • Engine undercover
• Front road wheels and tires • Front fender protector (RH and LH): Refer to EXT-22, "Exploded View". • Drive belt: Refer to EM-20, "Removal and Installation". • Engine cover: Refer to EM-25, "Exploded View". • Battery and battery tray: Refer to PG-124, "Exploded View". • Air duct, air cleaner case assembly and air cleaner body assembly: Refer to EM-26, "Exploded View". • Radiator hose (upper and lower): Refer to CO-17, "Exploded View". • Radiator cooling fan assembly: Refer toCO-20, "Exploded View". • Exhaust front tube: Refer to EX-5, "Exploded View".

• Alternator: Refer to CHG-30, "MR16DDT : Exploded View".

Engine Room LH
1. Disconnect all connections of engine harness around the battery, and then temporarily secure the engine harness into the engine side.

CAUTION:
Protect connectors using a resin bag against foreign materials during the operation.
2. Disconnect fuel feed hose quick connector. Refer to EM-43, "Exploded View". 3. Disconnect heater hoses. Refer to CO-26, "Exploded View". 4. Disconnect control cable from transaxle. Refer to TM-273, "Exploded View".

5. Remove EVAP hoses. Refer to EM-28, "Exploded View".

Engine Room RH
1. Disconnect vacuum hose from intake manifold. Refer to EM-28, "Exploded View". 2. Remove A/C compressor. Refer to HA-86, "Exploded View".

3. Remove ground cable at engine side.

Vehicle Underbody
1. Remove ground cable at transaxle side. 2. Remove rear propeller shaft. Refer to DLN-121, "Exploded View". 3. Remove drive shafts (RH and LH). Refer to FAX-21, "Exploded View".

4. Remove rear torque rod (1).

2 : Rear engine mounting bracket : Vehicle front


5. Remove stabilizer connecting rod. Refer to FSU-16, "Exploded View".

5. Remove stabilizer connecting rod. Refer to FSU-16, "Exploded View". 6. Rear front suspension member. Refer to FSU-18, "Exploded View".

7. Preparation for the separation work of transaxle is as follows: • Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to EM-40, "Exploded View".

Removal
1. Use a manual lift table caddy (commercial service tool) (A) or equivalently rigid tool such as a transmission jack. Securely support bottom of the engine and the transaxle assembly.

CAUTION:
Put a piece of wood or an equivalent as the supporting surface, secure a completely stable condition.
2. Remove upper torque rod (1) and engine mounting insulator

2. Remove upper torque rod (1) and engine mounting insulator (RH) (2).

: Vehicle front


3. Remove engine mounting bracket (LH).

3. Remove engine mounting bracket (LH).

4. Carefully lower jack, or raise lift to remove the engine and the transaxle assembly. When performing work, observe the following caution.

CAUTION:
• Check that no part interferes with the vehicle side. • Before and during this lifting, always check if any harnesses are left connected. • During the removal, always be careful to prevent the vehicle from falling off the lift due to changes in the center of gravity.

• If necessary, support the vehicle by setting jack or suitable tool at the rear.

Separation

1. Install engine slinger to front cover front left side (A) and cylinder head rear right side (B).

Slinger bolts : Engine front


Slinger bolts
Front cover front left side: ft-lb): 33 N·m (3.4 kg-m, 24
ft-lb)
Cylinder head rear right side: ft-lb): 25 N·m (2.6 kg-m, 18
ft-lb)

2. Remove starter motor. Refer to STR-27, "MR16DDT : Exploded View".

2. Remove starter motor. Refer to STR-27, "MR16DDT : Exploded View".

3. Lift with a hoist and separate the engine from the transaxle assembly. Refer to TM-301, "Exploded View" (CVT models).

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
• Never allow engine oil to get on engine mounting insulator. Be careful not to damage engine mounting insulator. • Check that each mounting insulator is seated properly, and tighten mounting nuts and bolts.

• When installation directions are specified, install parts according to the direction marks on them referring to the figure of components. Refer to EM-59, "4WD : Exploded View".

4WD : Inspection

INSPECTION AFTER INSTALLATION

Inspection for Leakage The following are procedures for checking fluids leakage, lubricates leakage, and exhaust gases leakage.

• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required quantity, fill to the specified level. Refer to MA-13, "Fluids and Lubricants". • Use procedure below to check for fuel leakage. - Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leakage at connection points. - Start engine. With engine speed increased, check again for fuel leakage at connection points. • Run engine to check for unusual noise and vibration. • Warm up engine thoroughly to check there is no leakage of fuel, exhaust gases, or any oil/fluids including engine oil and engine coolant. • Bleed air from lines and hoses of applicable lines, such as in cooling system.

• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the specified level, if necessary.

*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.

*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.