Clutch

Clutch disc and clutch cover

In this manual: Clutch
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

Except for K9K : Exploded View

HR16DE

1. Flywheel

1. Flywheel
2. Clutch disc
3. Clutch cover
4. Input shaft

A. First step
B. Final step

: Apply lithium-based grease: N·m (kg-m, ft-lb)
including molybdenum disulphide.: Apply lithium-based grease
including molybdenum disulphide.

MR16DDT

1. Flywheel

1. Flywheel 2. Clutch disc 3. Clutch cover 4. Input shaft

A. First step B. Final step

: Apply lithium-based grease: N·m (kg-m, ft-lb)
including molybdenum disulphide.: Apply lithium-based grease
including molybdenum disulphide.

Except for K9K : Removal and Installation

CAUTION:
• Never reuse CSC (Concentric Slave Cylinder). Because CSC slides back to the original position every time when removing transaxle assembly. At this timing, dust on the sliding parts may damage a seal of CSC and may cause clutch fluid leakage. Refer to CL-27, "Removal and Installation". • Never bring any grease to the clutch disc facing, pressure plate surface and flywheel surface.

• Never clean clutch disc using solvent.

REMOVAL

1. Remove transaxle assembly. Refer to TM-30, "Removal and Installation" (RS5F92R), or TM-84, "MR16DDT : Removal and Installation" (RS6F94R).

2. Remove clutch cover mounting bolts while holding clutch cover.

CAUTION:
Never drop clutch disc.

3. Remove clutch cover and clutch disc.

CAUTION:
Never drop clutch disc

.

INSTALLATION

1. Clean clutch disc and input shaft splines to remove grease and powder arisen from abrasion.

2. Apply recommended grease to clutch disc (1) and input shaft (2) splines (A).

CAUTION:
Be sure to apply grease to the points specified. Otherwise, noise, poor disengagement, or damage to the clutch may result. Excessive grease may cause slip or judder. And if it adheres to seal of CSC, it cause clutch fluid leakage. Wipe out excess grease. Wipe out any grease oozing from the parts

.

3. Install clutch disc, using a clutch aligner (A) [Commercial service

3. Install clutch disc, using a clutch aligner (A) [Commercial service tool]. 4. Install clutch cover, and then temporarily tighten clutch cover mounting bolts. 5. Tighten clutch cover mounting bolts to the specified torque evenly in two steps in the numerical order as shown in the figure.

6. For the next step and after, install in the reverse order of removal.

Except for K9K : Inspection

Except for K9K : Inspection

NSPECTION AFTER REMOVAL

Clutch Disc

• Measure circumferential runout relative to clutch disc center spline.

If it is outside the specification, replace clutch disc.

Runout limit/diameter of the area to be measured : Refer to CL-35, "Clutch Disc".

• Measure backlash to clutch disc spline and main drive gear spline at the circumference of clutch disc. If it is outside the specification, replace clutch disc.

Maximum allowable spline backlash (at outer edge of disc) : Refer to CL-35, "Clutch Disc".

• Measure the depth “A” to clutch disc facing rivet heads, using a

• Measure the depth “A” to clutch disc facing rivet heads, using a calipers. If it exceeds the allowable wear limit, replace clutch disc.

Facing wear limit (depth to the rivet head) “A” : Refer to CL-35, "Clutch Disc".

Clutch Cover

Clutch Cover
• Check clutch cover thrust ring for wear or breakage. If wear or breakage is found, replace clutch cover.

NOTE:
• Worn thrust ring will generate a beating noise when tapped at the rivet with a hammer. • Broken thrust ring will make a clinking sound when cover is shaken up and down.

• If a trace of burn or discoloration is found on the clutch cover pressure plate to clutch disc contact surface, repair the surface with sandpaper. If surface is damaged or distorted, replace clutch cover.

INSPECTION AFTER INSTALLATION

Clutch Cover Check diaphragm spring lever claws for unevenness with the lever still on the vehicle. If they exceed the tolerance, adjust lever height, using the diaphragm adjusting wrench (A) [SST: ST20050240].

Tolerance for diaphragm spring lever unevenness : Refer to CL-36, "Clutch Cover".

K9K : Exploded View

K9K : Exploded View

1. Flywheel

1. Flywheel
2. Clutch disc
3. Clutch cover
4. Input shaft

A. First step B. Final step

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
K9K : Removal and Installation: N·m (kg-m, in-lb)


K9K : Removal and Installation

CAUTION:
• Never reuse CSC (Concentric Slave Cylinder). Because CSC slides back to the original position every time when removing transaxle assembly. At this timing, dust on the sliding parts may damage a seal of CSC and may cause clutch fluid leakage. Refer to CL-27, "Removal and Installation". • Never bring any grease to the clutch disc facing, pressure plate surface and flywheel surface.

• Never clean clutch disc using solvent.

REMOVAL

1. Remove transaxle assembly. Refer to TM-86, "K9K : Removal and Installation".

2. Remove clutch cover mounting bolts while holding clutch cover.

CAUTION:
Never drop clutch disc.

3. Remove clutch cover and clutch disc.

CAUTION:
Never drop clutch disc.

INSTALLATION

1. Clean clutch disc and input shaft splines to remove powder arisen from abrasion. 2. Install clutch disc, using a clutch aligner (A) [Commercial service tool]. 3. Install clutch cover, and then temporarily tighten clutch cover mounting bolts. 4. Tighten clutch cover mounting bolts to the specified torque evenly in two steps in the numerical order as shown in the figure.

5. For the next step and after, install in the reverse order of removal.

K9K : Inspection

K9K : Inspection

INSPECTION AFTER REMOVAL

Clutch Disc
• Measure circumferential runout relative to clutch disc center spline.

If it is outside the specification, replace clutch disc.

Runout limit/diameter of the area to be measured : Refer to CL-35, "Clutch Disc".

• Measure backlash to clutch disc spline and main drive gear spline at the circumference of clutch disc. If it is outside the specification, replace clutch disc.

Maximum allowable spline backlash (at outer edge of disc) : Refer to CL-35, "Clutch Disc".

• Measure the depth “A” to clutch disc facing rivet heads, using a

• Measure the depth “A” to clutch disc facing rivet heads, using a calipers. If it exceeds the allowable wear limit, replace clutch disc

Facing wear limit (depth to the rivet head) “A” : Refer to CL-35, "Clutch Disc".

Clutch Cover

Clutch Cover
• Check clutch cover thrust ring for wear or breakage. If wear or breakage is found, replace clutch cover.

NOTE:
• Worn thrust ring will generate a beating noise when tapped at the rivet with a hammer.

• Broken thrust ring will make a clinking sound when cover is shaken up and down.

• If a trace of burn or discoloration is found on the clutch cover pressure plate to clutch disc contact surface, repair the surface with sandpaper. If surface is damaged or distorted, replace clutch cover.

INSPECTION AFTER INSTALLATION

Clutch Cover
Check diaphragm spring lever claws for unevenness with the lever still on the vehicle. If they exceed the tolerance, adjust lever height, using the diaphragm adjusting wrench (A) [SST: ST20050240].

Tolerance for diaphragm spring lever unevenness : Refer to CL-36, "Clutch Cover".

Service data and specifications (SDS)