Driveline transfer: TY21B

Drive pinion

In this manual: Driveline transfer: TY21B
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Exploded View

1. Pinion lock nut

1. Pinion lock nut
2. Companion flange
3. Drive pion oil seal
4. Pinon rear bearing
5. Transfer case
6. Gasket
7. Filler plug
8. Collapsible spacer
9. Drive pinion adjust shim 10. Drive pinion
11. Pinion front bearing 12. Ring gear
13. Ring gear shaft
14. Ring gear bearing (right) 15. Ring gear bearing adjust shim (right) 16. Spacer (right)
17. Transfer case oil seal (right) 18. Drive shaft oil seal 19. Transfer cover
20. Oil defense
21. Ring gear bearing (left) 22. Ring gear bearing adjust shim (left) 23. Spacer (left)
24. Transfer case oil seal (left) 25. Drain plug
26. Dowel pin

A. Oil seal lip
B. Transfer case mounting face

: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly. : Apply anti-corrosive oil.: Apply gear oil.
: Apply multi purpose grease: Apply anti-corrosive oil.
: Apply Genuine Liquid Gasket 1215: Apply multi purpose grease
or equivalent.: Apply Genuine Liquid Gasket 1215
or equivalent.

Disassembly: Select with proper thickness.


Disassembly

1. Remove transfer cover. Refer to DLN-114, "Disassembly". 2. Remove ring gear shaft assembly. Refer to DLN-96, "Disassembly". 3. Remove lock nut from the drive pinion.

4. Put matching marks (A) on screw ends of companion flange (1) and drive pinion.

CAUTION:
Use paint to avoid scratching the surface.
5. Remove companion flange from drive pinion with a puller (A).

5. Remove companion flange from drive pinion with a puller (A).

6. Remove drive pinion oil seal from the transfer case with a puller

6. Remove drive pinion oil seal from the transfer case with a puller (A) (SST: KV381054S0).

CAUTION:
Never damage transfer case.
7. Remove drive pinion assembly (1) from transfer case while tapping

7. Remove drive pinion assembly (1) from transfer case while tapping the drive pinion lightly with a plastic hammer.

CAUTION:
Never drop the drive pinion assembly.
8. Remove collapsible spacer from the drive pinion.

9. Remove inner race of drive pinion bearing (rear side) from transfer case.

10. Remove inner race of drive pinion bearing (front side) from drive

10. Remove inner race of drive pinion bearing (front side) from drive pinion with a replacer (A) (commercial service tool). 11. Remove drive pinion adjusting shim from the drive pinion.

12. Perform inspection after disassembly. Refer to DLN-111, "Inspection".

Assembly

Assembly

1. Select drive pinion adjusting shim. Refer to DLN-98, "Adjustment". 2. Install selected drive pinion adjusting shim to drive pinion.

3. Install inner race of drive pinion bearing (front side) to drive pinion with a drift (A) (SST: ST35272000).

CAUTION:
• Never reuse drive pinion bearing (front side).

• Apply gear oil to the drive pinion bearing (front side).

4. Assemble the inner race of drive pinion bearing (rear side) into the transfer case.

CAUTION:
• Never reuse drive pinion bearing (rear side).

• Apply gear oil to the drive pinion bearing (rear side).

5. Install drive pinion oil seal to transfer case with drifts so that it

5. Install drive pinion oil seal to transfer case with drifts so that it becomes flush with case end surface with the drifts (A and B).

A : Drift (SST: KV38102510) B : Drift (SST: ST30720000)

CAUTION:
• Never reuse oil seal.

• Apply multi-purpose grease onto oil seal lips, and gear oil onto the circumference.

6. Assemble a collapsible spacer onto the drive pinion.

6. Assemble a collapsible spacer onto the drive pinion.

CAUTION:
Never reuse the collapsible spacer.

7. Assemble drive pinion assembly into the transfer case, and then install companion flange (1) to drive pinion.

NOTE

:
Align matching marks (A) on the thread edge of companion flange and drive pinion and install companion flange if drive pinion is reused.

8. Tap the companion flange (1) with a plastic hammer as far as

8. Tap the companion flange (1) with a plastic hammer as far as the lock nut can be tightened.

CAUTION:
Never damage drive pinion oil seal.

9. Apply anti-corrosive oil to the thread and seat of the lock nut, and temporarily tighten lock nut to the drive pinion.

CAUTION:
Never reuse lock nut.

10. Tighten lock nut within the specified torque range with a preload gauge (A) (SST: ST3127S000) so that the drive pinion bearing preload is within standard.

Drive pinion bearing preload : Refer to DLN-117, "Preload Torque".

CAUTION:
• Start the tightening of lock nut from lower limit of the specified torque. Check the preload every 5° to 10° while tightening the lock nut. • Replace the collapsible spacer and tighten it again to adjust if preload exceeds the specified value. Never loosen lock nut to adjust preload.

• After adjustment, rotate the drive pinion back and forth from 2 to 3 times to check for unusual noise, sticking, binding, and so on.

11. Install ring gear shaft assembly. Refer to DLN-97, "Assembly". 12. Install transfer cover. Refer to DLN-114, "Assembly".

13. Check backlash, tooth contact, total preload and companion flange runout. Refer to DLN-98, "Adjustment".

CAUTION:
Measure the total preload without the transfer case oil seal.

Adjustment

About adjusting of drive pinion, refer to DLN-98, "Adjustment".

Inspection

INSPECTION AFTER DISASSEMBLY

Check items below. If necessary, replace them with new ones.

Gear and Shaft Check gear face and shaft for wear, cracks, damage, and seizure.

CAUTION:
Replace ring gear and drive pinion as a set (hypoid gear set) if any malfunction is detected on the ring gear or drive pinion.

Bearing
Check for seizure, peeling, wear, corrosion, sticking, unusual noise, roughness in hand turning, and other damage.

CAUTION:
Always replace inner race and outer race as a pair when replacing the bearing.

Shim
Check for seizure, damage, and unusual wear.

Case
Check the bearing mounting surface for wear, cracks and damages.

CAUTION:
Replace transfer case and transfer cover as a set if any malfunction is detected on transfer case or transfer cover.